Pump

Thanks for very quick delivery and detailed instructions found on this site. I followed the step-by-step instructions and everything went as planned with one exception, I installed the V-belt in a wrong way after replacing the pump. Next time, I will mark or remember the way belt sits between the motor and the pump.
I found a small sock in the pump. Pump itself was still good (I think), but I installed new one along with new belt (just in case).

First, I removed the screws, then removed the pump. I, then, installed a new pump.

Unpluged washer, turned off water supply, removed front covers, removed spring on right side to allow drum to lean over, removed the 2 hoses from pump, removed motor (4 bolts), removed 3 screws holding pump. Installed a new belt and replaced the pump. I replaced the hoses on the pump, replaced the spring, and turned on the water, plugged in the washer, turned it on and hoped for the best. Worked fine, no leaks or problems.

replaced belt that was wore out. decided to replace pump while I had washer apart.

Removed front cover of machine. Removed motor/pump assembly which was held in by four (4) bolts. At the same time removed belt from transmission pulley. Removed pump assembly from motor, held in by three (3) torx fasteners. Before installing new pump installed new belt on motor assembly. While setting the motor/assembly in place threaded belt around transmission pulley. Fastened motor/pump assembly. Very easy process!

I seemed to have a more difficult time changing the pump out than others who had left their instructions on line prior to me.
What I has to do is remove the 4 bolts that secured the motor & mount to the frame. I then unplugged the wire harness from the motor leads.
I removed the belt tensioning spring & removed the belt.
I then removed the motor, motor mount and pump assembly. Turned it upside down & removed the pump. When installing the new pump you will need to remember how the belt was routed. A local parts house actually gave me a xeroxed schematic that showed me how to route it. A real life saver.
After that I turned the assembly right side up, bolted the mount into place, installed the new belt onto the large flywheel, attached the belt tension spring, plugged in the wiring harness and ran a rinse cycle. No leaks. Good as new.
Yes. It took a little longer than expected. But it was alot cheaper than having a service man do it.

We noticed that water was on the ground of the laundry room. We initially thought that the washer was leaking. Realized that the washer was going on the spin cycle without draining the water which caused the water the slosh over the edges and then leak on the floor. Well, I had to remove all the wet clothes and suck the water out with a shop vaccuum-this actually took most of the time. After taking the front of the washer off, we noticed the water pump was stripped out. After removing the pump, we then noticed one of our kid's socks jammed in the pump. How the sock got there is still a mistery. We found the replacement part on PartSelect and ordering was easy and fast. Thanks. We're washing clothes again.

Unhooked the idler pully spring, removed the 2 hoses from the pump outlets, unhooked the idler pulley srring to slaken the drive belt tension, removed 4 bolts from the motor mount to drop the motor, and slipped the drive belt off the transmission pulley.

Removed 3 torx screws that secure the pump. The pump was stuck to the motor motor shaft from corrosion and had to knock the pump off with a hammer. Reassembly was a breeze.

The most serious problem I had was a black widow spider lurking under the transmission pulley. Never did get it!

First I unscrewed the bottom of the front panel.
Then I realized the front panel pulls off from the top.
(manuals are helpful only if read!) I took the tub hose off at the tub and used my wet vac to remove all the excess water. (no towel needed) Using the appropriate size torx head bit, an extension and a small socket wrench to undo the screws holding the pump. I had to push and pull the bottom of the tub slightly to get proper room for the small socket wrench. pull the pump down and off. take the hoses off and place them on the new pump. reverse the process. tighten the clamps and replace the front cover.

removed sheetmetal screws hilding motor bracket loosened hose clamps on both hoses and removed hoses., rmoved 3 screws holding the pump in and slid pump off of shaft. installation was reverse

I removed the 4 bolts that hold the drive motor in place, then tipped the motor on it's side and removed the 3 allen screws that hold the pump in place. Then just reversed the process.

I ordered my part on Monday. It was delivered on Tuesday, and by four o'clock we were in business. I highly reccomend PartSelect.

remove front panel. unplug motor. remove 4 screws and take motor,pump,idler and belt assembly out. remove pump from bottom of motor. 3 screws held pump and drove off with hammer. replace idler and install belt before new pump. install pump. reinstall assembly. works good now.

Just took it apart and figured out what was leaking. Ordered a piece online through Partselect. Got the piece in 2 days and put it back together. Went real smooth, saved us from buying a new washing machine. Thanks! My husband is quit the handy man too! So I thank him too!

I removed the front lower panel. I disconnected the springs holding the motor to the chassis. I removed the belt off the pump pulley. Pay attention to the way the belt runs from the pulley and through the pump. This will aid in placing the pump back on so the belt runs correctly. Disconnected the wires, removed the capacitor bracket so I could take the motor/pump unit out after I removed the 4 bolts holding the motor/pump unit. Removed the 3 torx screws holding the pump to the motor. Matched the new pump to the old to make sure the new one was correct.

Installed in reverse order.