Water Inlet Valve

took hose off then took three 5/16 screws then clamp off reversed order to put back on check for leaks ok

Removed the front of the washing machine. Located & removed the water inlet valve from it's mounting on the back
inside face of machine. Replaced water valve, & restarted machine. Like new again!

Can't say enough about the speed of parts delivery & professionalism and accuracy recieved from the team at Parts Select. Thanx again,

Greg W.

pulled the front panel first, then lifted the top(2bolts in each).
Then unhooked water and unbolted the water inlet valve from the back left corner behind the tub.four wires are connected Pay attenion to where they go, for easy reinstallation.NOTE: watch the clips in the front of the washer they flew off and it took half an hour on the internet finding out how they went back on.

Simple removal of the mounting plate holding the old valve to the rear of the machine followed by disconnection of the water hose to the washer from the valve and unplugging of four electrical connections. Reattached the new valve to the water hose and then reattached the new valve to the mounting plate, finally reconnecting the wiring connections (4). Installation completed by reattaching the valve mounting plate to the washer. The diagnosis was confirmed by blowing into the old valve's water inlet. Air would pass through the valve, confirming that it did leak when the valve was closed. Air blown through the new valve prior to installation would not pass through the new valve.

My experience with my repair is as follows:
After determining the "hot water" solenoid was weak and that a new fill valve was needed, I placed my order with PartSelect on Thursday and to my suprise, had it in my hand Friday evening (no special shipping). WOW talk about fast! But unfortunately the part was broken.
Called PartSelect back Saturday morn to explain my problem and was told that I would be credited for the broken part and that a replacement would be sent ASAP probably arriving on Wednesday. Again to my suprise, the part arrived on Tuesday morning.
Hats off to you guys for great service, prices and no hassles.

Dennis Fleming
North Billerica, MA

I took the hot and cold water hoses off with pliers.and then I took the one screw out towards the top of the water inlet valve plate.disconnected 4 wires,there is a small clamp on the small hose on the valve you have to remove.and last there is a cluster of wires that has to be removed from a bracket and (it is important to put these cluster of wires back in place otherwise they will wear a bare spot in them.)

Exactly as the video showed. This was a very simple repair. The only extra thing I did was to replace the mesh screen/gasket at the hose ends. They were plugged with crud. PartSelect saved me from buying a new washing machine. Yay!

Removed old part, installed new part. tested machine. worked fine.

First let me commend PartSelect for their incredibly fast shipping. Ordered on a Thursday and it arrived on Friday!!

The repair itself was fast and easy and let me add I had never worked on a washing machine before.

1)Unplugged power cord from the wall.
2)Turned off hot and cold water at the shutoff valves.
3)Disconnected water lines leading to the washer.
4)Removed 3 screws holding the bracket assembly on the washer.
5)Removed bracket and pulled water inlet valve out a few inches.
6)Held new inlet valve in same orientation as the old one and then one by one removed the four electrical wires from the old solenoids and attached them to the corresponding place on the new inlet valve.
7)Put inlet valve back in place, attached bracket, and secured it with the 3 screws.
8)Attached water lines to inlet valve and plugged power cord back in.
9)Turned water back on at shutoff valve and checked for leaks.

I washed a load of clothes after the repair and am happy to report that the hot water now runs in as fast as it did when the machine was new. This washer may be 30 years old but I think the old gal's got some life left in her yet.

open top of washer
remove two screws that hold water inlet valve
disconnect four wires and hose;replace new water inlet valve and reversed operation
everything went well

I ordered the water valve at 12:42 PM one day and received the part at 10:25 AM the next morning. Now this is what I call excelent service. The price of the part was very reasonable. Getting my wife off my back for her washer being broken PRICELESS.

Pushed machine out from wall; disconnected the supply hoses (after closing the valves at the wall); unplugged electrical cord; removed two wires from the solenoid connectors; removed two screws that secure valve assembly to backplane of machine. Installation of new assembly was the opposite procedure. We have private well, and silt was plugging the cold water side of valve. So, I also installed a large sediment filter behind the washer, so this will never happen again.

Disconnected the hot/cold water hoses. Removed screw that holds water valve in place. Removed two screws that hold valve to metal plate. Disconnected wire terminals from old valve and installed on new valve on the same spades. Disconnected water discharge line by loosing screw that hold line on valve, reattach to new valve. Removed old valve from plate, installed new one with the two screws to plate, then put in place and put in screw that hold valve in back of washer. Connected hot/cold hoses and fired it up and noisy water eliminated. About 30 minutes and back in service which made the wife happy that her washer was quite again. Thanks!

1. Removed hoses 2. Removed inlet valve. 3. Took valve apart to discover defect in diaphram. 4. Looked up and ordered part. 5. Replaced inlet valve. 6. Tested washer.

I followed steps outlined on you web page.

First I remove the hot & cold water hoses using an adjustable wrench. I then unscrew the panel that holds the water inlet valve using a nut driver. I then carefully pull out the panel, moving the harness wires out of the way, so that I can loosen the clamp holding the inside rubber tube. I remove the old water inlet valve from the panel by removing the 2 screws and then put the new one in. I then reconnect the rubber tube and tighten the clamp. I then screw back the panel and reconnect the hot & cold water hoses. It took me about 20 mins to complete the job.