1583805-1-M-Whirlpool-205613-Water-Inlet-Valve.jpg
1583805-1-S-Whirlpool-205613-Water-Inlet-Valve.jpg 1583805-2-S-Whirlpool-205613-Water-Inlet-Valve.jpg 1583805-3-S-Whirlpool-205613-Water-Inlet-Valve.jpg

Water Inlet Valve

PartSelect Number PS1583805

This part has two ports for water to enter. It is blue and is intended for use with many washing machines and comes with a multi-mount bracket and an outlet adaptor.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • No hot or cold water.
  • Will not stop filling with water.
  • Leaking water.
  • Will not fill with water.
  • Unusual Noise.
  • Compare At

    $33.02
  • You Save

    $5.50
  • Your Price

    $27.52
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.0 / 5.0, 78 reviews What's this?
 

1 of 1 people found this instruction helpful

Parts Used

  • Water Inlet Valve

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsPliers, Screw drivers, Socket set

CustomerTina from The Plains VA

Washer filling up with water when idle

I removed the two hoses connected to the valve, then I removed the front panel by removing two screws on the bottom. I disconnected a drum hose connected to the top, tilted the top back, then separated the inlet valve from its metal housing by removing the screws holding it in place. I then removed the metal housing in order to have more access to the old valve. At this point, the valve was only held in place by a few wires. I noted which wires connected where and how the valve was oriented (Hot/Cold position), then removed the wire connections with pliers by grasping the connectors (not the wires). I then reversed this process to install the new valve.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Water Inlet Valve

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Screw drivers, Socket set

CustomerBryan from Lodi WI

Small water leak from the water inlet valve

Removed 2 screws on the bottom of the front of the washer and pried the front off. Then removed 2 more screws for the top of washer and rocked it back to expose the water inlet vavle. Removed the water inlvet vavle and replaced it. Then put it all back together. Done

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Water Inlet Valve

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Screw drivers

CustomerJeff from Diamond Bar CA

Low cold water flow during fill

Part shipping was great got here in two days-

I pulled off Front panel (two screws) and lifted Top panel (2 screws) and disconnected the inlet hoses. I removed the old Inlet valve. (1 scew and valve to tub hose connection).

Before Installing the new valve, i shifted the connector positions on the selenoids to match the old valve. and installed by reversing the steps. All went very smooth. Thanks, It was easy.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Water Inlet Valve

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Screw drivers

CustomerALISA from Kathleen GA

Hot water would not full shutoff during cycles, causing over flow

When the part came in, it was just a matter of getting the old part out, and replacing it! Incredibly smooth---the hold down screws were obvious, so once I got them out---the part came out of the machine, I disconnected the two control wires, reconnected them to the new part---and reinstalled!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Water Inlet Valve

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers, Wrench(Adjustable)

CustomerEric from Brook Park OH

Water inlet valve had a crack and was leaking water.

I first shut off the cold and hot water hoses so that no water would run while replacing the part. After that I made sure to unplug the washer .Then I removed the plate that was holding the water inlet valve with a 1/2 " nut driver ,I think there were four bolts .Then I removed two more bolts from the center of the plate that were holding the water inlet valve.I then disconnected one 1/4 " screw or I should say loosened one which held the main water hose going into the washer which then released the part ,except from four wires. I then took one wire off at a time and attached to the new part one at a time.Finally, I was finished and reconnected everything .It worked perfected !I'am very happy and pleased . This washer is over 25 years old and still runs .

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

  • Water Inlet Valve

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers, Wrench set

CustomerTevis from Albemarle NC

Cold water would not enter washer.

Change the position of electrical connection on inlet valve before installation to match positions of old valve. Shut off electricy and water to washer. Disconnected water hoses, and power wires to old valve. Removed old valve and installed new valve exactly as installed on old valve. Washer operated perfectively

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 3 people found this instruction helpful

Parts Used

  • Water Inlet Valve

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsPliers, Screw drivers, Socket set

CustomerPaul from San Antonio TX

Washing machine was filling very slowly

I checked the inlet hoses for hard water build up and noted that this was not a problem. Then checked the hose from the inlet valve to the washer drum and determined that it was clear so I knew the problem was a faulty inlet valve. After receiving my replacement valve, I removed the old valve by removing the hot and cold water hoses and unscrewing two screws securing the inlet valve and lifting the inlet valve out the metal holding bracket. This gave me complete access to the inlet valve allowing me to remove the hose clamp and hose to the washing machine drum. The new inlet valve was an exact match so I removed the four electrical wires one by one while putting them back on the new inlet valve to insure correct electrical connections. I added a piece of one half inch plastic tubing provided with the new inlet valve on the outlet nipple of the new inlet valve to prevent leaking. I then put the new inlet valve back into the holding bracket and screwed it down. I replaced the hot and cold hoses to the new inlet valve carefully so as not to cross thread the plastic connection on the new inlet valve. After turning the water back on, I checked for leaks and plugged the washing machine back on to test it with a washing cycle.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 3 people found this instruction helpful

Parts Used

  • Water Inlet Valve

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers

CustomerCas from Cary NC

After first spin, cold water comes in for rinsh, the water would not come in, but would run out on floor.

Removed old valve and replaced with new. Wire for wire..screw for screw..

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Water Inlet Valve

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerRichard from Paducah KY

Old water valve assembly cold water solenoid valve was leaking thru.

Shut off water supply, unplugged washer power, removed supply hoses from old washer valve assembly, removed valve mounting plate and removed old valve assembly from mounting plate, diagrammed and disconnected hot and cold solenoid valve wiring and removed valve assembly outlet hose. Installed and connected new valve, performing the preceding steps in reverse order. pressurized new valve, verified valve function and checked for leaks and placed washer back in service.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:1- 2 hours

ToolsNutdriver, Socket set

CustomerAustin from Cupertino CA

Groaning / squeaking sound from water inlet valve

When the inlet valve closed, after dispensing water, it did so slowly and with a groan or squeak. Same during rinse & spin.

The video was clear on how to get it out from the back and replace with a new unit. Only problem I had was not pushing the outlet hose all the way back down onto the new inlet valve -- it leaked pretty dramatically but was an easy fix.

When pulling the inlet valve, I saw the inlet hoses where starting to slightly leak at their connectors, so I replaced them.

As I had never replaced the belts on this 20+ year old Maytag, I swapped them out at the same time. All I had to do is tilt the washer back and pull off the old belts & replace them in reverse order.

The videos were a great help.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Water Inlet Valve

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsPliers, Screw drivers

CustomerRichard from Hampden MA

Dishwasher power shutdown mid cycle

Removed door panel to get to the electric control conponents and noticed a burned wire to one of the door microswitches. Ordered the door switch repair kit from PartSelect. Also, ordered and replaced the thermal fuse at the same time since it was only $12 and didn't know if that blew at the same time the switch cooked. I had the parts coming standard delivery (3-5 days), but they arrived the very next day. Parts included easy to follow directions.Job went pretty smooth and the dishwasher works again Good experience!

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Water Inlet Valve

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsPliers, Screw drivers, Socket set

CustomerLADDIE from HUTSONVILLE IL

Water would not shut off. T

Followed web instructions.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Water Inlet Valve

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsNutdriver, Screw drivers

CustomerBruce from Troy MI

Washer would not fill unless "cold" setting selected.

I watched a sample repair on YouTube and read the instructions that came with the part. All went as planned/described.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Water Inlet Valve

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers, Socket set

CustomerMartha from Red Bluff CA

Water leaking, slow fill

I had taken the washer out and replaced both hoses, and the leak stopped for a load or two. I then replaced the water inlet valve, because I could see that the plastic threads were pretty bad. The repair is very simple on this model. There is no need to open the cabinet at all, the entire job is done on the back. I used a socket and the stubby driver for the mounting screws and switched to a screwdriver tip and opened the clamp on the hose leading to the air gap assembly. The entire operation took about five minutes. The repair worked for two or three loads.

The water leak came back, so after some searching I finally figured out how to open the cabinet, and that took longer than actually doing it. The front opens with two big screws located on the front about 4" above the floor, just in the corner of the indentation on the panel.

With the top tipped up (tape the lid!) out of the way, the leak proved to be coming out of the air gap assembly. There is an injector nozzle and a rubber sleeve that goes over it. They fit in the large black hose. I easily opened the hose clamp, removed the old parts, put in the new one. The rubber sleeve has a cover that goes over the edge of the plastic injection nozzle. You have to make sure it is entirely and smoothly inserted. Easy. Then insert it all the way to the shoulder of the end of the hose with that wide end facing into the hose and the other end open. Slip the open end through the bracket and into the other hose. Tighten all your clamps, and carefully pressure test. Do not touch any metal parts if there is water spewing. Just turn it off, pull the plug, and fix the problem. In my case, it worked perfectly, and I turned it off, replaced the front and the job was done.

Despite the great advice I got here, I ended up getting the nozzle parts in town. I had to go to an appliance parts outlet rather than a place like Home Depot, but it was quick and no shipping. Still, I would not have tried this without the great advice and fast service here.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

  • Water Inlet Valve

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerRichard from Petersham MA

Very slow cold water inflow

1. Identify washer model and symptom
2. review page of suggested part; view installation video
3. order part with standard shipping
4. receive part next day and install just as the video showed

Entire job from going to PartSelect website to completion took less than 24 hours. Hardest part was moving the washing machine. Machine is nineteen years old and now works perfectly. Unmatched service.

Help other customers find the most helpful instructions.

Were these instructions helpful?