| |
0 of 1 people found this instruction helpful
Parts Used
-
- Flat Style Oven Igniter Kit
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerAudrey from Houston TX
Oven would ignite sometime, sometime not. Always argued with the broiler when it was lit first.
My son removed the pan above the ignition switch, using only a screwdriver. He checked it against the excellent website photos for compatibility with what you had to offer. I order it and it was here in Houston within 2 days of the order. Took 20 minutes to remove and compare and 7 minutes to replace the old with the new. A piece of cake.
Best thing was that the oven/stove is 29 years old and I thought I would have to buy a new one (approximately $700 for comparable)and I am a Senior Citizen. So for $48.98 and lots of elbow grease to clean the stainless steel top etc. I have a dandy, operating, dependable piece of cooking equipment !!!!
|
0 of 1 people found this instruction helpful
Parts Used
-
- Flat Style Oven Igniter Kit
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerJason from Williamsburg VA
Oven making whooshing sound and not heating up
Pulled oven out from wall. Unplugged. Pulled out bottom drawer. Removed oven door by pulling up on angle. Removed bottom of oven. Removed old ignitor by taking out screws. Disconnected red and white wiring plastic coupler. Fed new wiring and connected. Mounted ignitor. Plugged back in. Very easy and worked!
|
0 of 1 people found this instruction helpful
Parts Used
-
- Flat Style Oven Igniter Kit
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsNutdriver
CustomerMIKE from Phelan CA
Oven quit lighting
I removed the old igniter, held in place with two screws, pulled the wiring out to get to the clip, and undid the clip. Clipped the new igniter to the wires, pushed back into the hole at the back of the oven, installed the igniter with the two screws, and fires just like new! I had a loose wire on the old igniter and hassled with that for years because I didn't realize how easy the fix was.
|
0 of 1 people found this instruction helpful
Parts Used
-
- Flat Style Oven Igniter Kit
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
Customerrick from chariton IA
Would not light oven
2 screws easy to remove and plug in the wire. job done.
|
0 of 1 people found this instruction helpful
Parts Used
-
- Flat Style Oven Igniter Kit
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsPliers, Screw drivers, Wrench(Adjustable)
CustomerSteve from Prospect Heights IL
The oven gas valve would not turn on
Replaced the oven ignitor. Toughest part was removing old screws.
|
0 of 1 people found this instruction helpful
Parts Used
-
- Flat Style Oven Igniter Kit
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerHELMUT from MIDDLE VILLAGE NY
The oven would not light even though the glow plug lit.
Remove the shelves and floor of upper oven and remove the two screws holding the glow plug. Disconnect wiring harness and replace with new one. Screw new glow plug and replace floor and shelves.
The oven worked like a charm again.
|
0 of 1 people found this instruction helpful
Parts Used
-
- Flat Style Oven Igniter Kit
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
Customerkenneth from breaux bridge LA
Oven would not light
open oven door remove bottom tray pull off two screws unplug wire remove old part install new part
|
0 of 1 people found this instruction helpful
Parts Used
-
- Flat Style Oven Igniter Kit
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerLINDA from SALEM OR
Would not heat. Broiler was fine, just no oven.
Well, this wasn't my first rodeo, this is the second ignitor I have replaced in my oven, first being the broiler. It is very simple, unscrew the old one, screw in the new one. The hardest part was cleaning up the mess I found UNDER THE OVEN!!!!
|
0 of 1 people found this instruction helpful
Parts Used
-
- Flat Style Oven Igniter Kit
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerLuz M. from North Providence RI
Oven didn't get hot
was very easy following the instruction in YOUR web site. I feel very thank full !!!!!, because you help me a lot!!!!!!
|
0 of 1 people found this instruction helpful
Parts Used
-
- Flat Style Oven Igniter Kit
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerOtto from Bridgeport CT
Ignitor lights but gas does not come on
Removed the 3 screws fastening the ign. bracket to pan housing & gas burner, pulled out the assy., removed the 2 wire nuts, removed the shield from old ign. ceramic, slipped in new ignitor ceramic, pushed the assy. back into pan opening, replaced the 3 screws & fired it up. Gas came on within 30 sec. of ignition. Put a pie in for 45min. & completed the cycle. Enjoyed the pie. Thanks for the help Parts Select.
|
0 of 1 people found this instruction helpful
Parts Used
-
- Flat Style Oven Igniter Kit
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsNutdriver, Screw drivers
Customermitch from brooklyn park MN
Oven didnt light
i removed old part, then installed new one. easy
|
0 of 1 people found this instruction helpful
Parts Used
-
- Flat Style Oven Igniter Kit
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsNutdriver
CustomerRichard from Farmington Hills MI
Oven would not work, broiler and range did work.
Came to this website to look for possible cause. The major fault for my problem was the igniter @ 61% of the time. So, I ordered this part @ about $55. Opened the range floor, removed two nut screws and old igniter, by unpluging. Plugged in new part reattached screws and tested before putting it back together. Worked fine, without snags. However I did pull up and remove oven door for complete access to oven.
Rick,
Detroit, MI.
|
0 of 1 people found this instruction helpful
Parts Used
-
- Flat Style Oven Igniter Kit
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerCarl from Delano CA
Oven would not ignite
I removed the various trays and racks to gain access to the oven igniter. I removed the one screw that held the wiring in place that goes into the body of the oven and pulled out the wires. I removed the wire nuts and safe ended the hot wires. I removed the two screws that held the igniter in place and replaced it with the new one. I reconnected the wiring with the wire nuts , pushed the wiring back into the body of the and stuffed new packing material into hole and reattached the plate on the back of the oven. Turned on the oven and it ignited immediately. A very easy job to complete. I would suggest to others to turn off the power. I knew what I was doing by working it "hot".
|
0 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsNutdriver, Pliers
CustomerPeter from Thousand Oaks CA
Two appliances died the same week
Oven Ignitor fell apart and Maytag had a thermal fuse (unresettable) blow. Got the parts, put them both in in under a half hour. Now I can eat Pizza in Clean Clothes!!!!
|
0 of 1 people found this instruction helpful
Parts Used
-
- Flat Style Oven Igniter Kit
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsNutdriver
CustomerRay from Valhalla NY
Oven would'nt preheat
Pulled out the plug, pulled out the stove, removed the oven door, pulled out the lower shelf and racks. Used a nutdriver to remove the 2 screws from the bracket, disconnected the old ignitor, new ignitor was an exact replacement, put back in the screws, pushed back the stove and plugged it back in....Was back in business in a matter of seconds!!
|