BBB A-Plus
1573892-1-M-Whirlpool-12400035-Flat-Style-Oven-Igniter-Kit.jpg
1573892-1-S-Whirlpool-12400035-Flat-Style-Oven-Igniter-Kit.jpg 1573892-2-S-Whirlpool-12400035-Flat-Style-Oven-Igniter-Kit.jpg 1573892-3-S-Whirlpool-12400035-Flat-Style-Oven-Igniter-Kit.jpg

Flat Style Oven Igniter Kit

PartSelect Number PS1573892

The flat style gas oven igniter included in this kit has a body length of 3-3/4 inches. This kit comes with all of the pieces you need to replace longer ceramic igniters, though this kit can also replace short igniters. This igniter has an amperage range of 3.3 - 3.6 and does NOT replace round style oven igniters.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Kenmore, Admiral, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Gas igniter glows but will not light
  • Little or no heat when baking
  • Will not start
  • Little or no heat when broiling
  • Oven not heating evenly
  • Cooktop element not heating
In Stock

  • Compare At

    $79.73

  • You Save

    $13.29

  • Your Price

    $66.44
Fast Shipping

Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos

For installing this part.

Installation Instructions

Provided by PartSelect customers like you.

< PREVIOUS 1 2 3 4 5 6 7 8 NEXT > 31-45 of 118

 

1 of 1 people found this instruction helpful

Parts Used

    • Flat Style Oven Igniter Kit

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerNola from Enid OK

Stove would not light to heat up.

REMOVED GRATES AND BOTTOM PLATE TWO SCREWS HOLDING IT. TURN OVEN LIGHT ON AND UNWIRE THE WIRE. UNSCREWED THE TWO SCREWS AND REPLACE. THIS TOOK MY HUSBAND ABOUT TEN MIN. AND FOR HIM HE SAYS THAT THIS WAS A WALK IN THE PARK. HE SAYS IF HE CAN DO IT ANYONE CAN. THIS WAS ONE OF THE EASY HONEY DEWS. GOOD LUCK WITH YOURS. NOLA & KEITH

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

    • Flat Style Oven Igniter Kit

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerELMER from BONNEY LAKE WA

Igniter was not getting hot enough to allow burner to come on.

took out two screws that held Igniter to burner, unbluged wires from behind and pulled them out to the front of over, replaced with new one, solved the problem of the burner not coming on,,,,

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

    • Flat Style Oven Igniter Kit

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerJoe from West Winfield NY

Oven would not light reliably.

Just like the example I removed the oven base, removed the two screws holding the igniter. Pulled out the wires opened the connector, plugged in the new igniter put everything back and turned on the oven. The oven now lights better than it did when new. And it holds a steady temp.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

    • Flat Style Oven Igniter Kit

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers

CustomerJohn from Wisconsin Rapids WI

The oven igniter lit up but the valve wouldn't release the gas to ignite.

I would have never guessed that the problem would have been with the igniter since it was glowing. After reading some of the entries in your trouble shooting area it was clear that this is common and that it likely was the igniter so I simply took off the two screws that hold it in place, inplugged the old, plugged in the new, secured with the screws and it worked. The only problem I encountered was that when I unplugged the old igniter the plug fell down into the bowels of the oven and I had to fish out with a twisted up hanger.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

    • Flat Style Oven Igniter Kit

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerBrian from Spotswood NJ

Oven would not heat up fully, smelled of gas.

Took off the top plate at the bottom of the oven, and the flame spreader, removed 2 screws on the igniter, pulled out the broiler tray and unplugged it. Took longer to get off the floor than it did to replace the part.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

    • Flat Style Oven Igniter Kit

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Screw drivers

CustomerMatt from Arlington AL

Oven was slow to get to temp and not holding temp

Thanks to previous posters, this seemed to be an igniter issue, and I found the idea of swapping the broiler igniter for the bottom one particularly good - I knew exactly what part was broken and how easy/hard the job would be prior to ordering. The part used snap in electric components, so the only work was in removing and re-installing the parts. Working in the oven was by FAR the most difficult part of the entire process.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

    • Flat Style Oven Igniter Kit

Level of DifficultyEasy

Time to do repair:Less than 15 mins

ToolsWrench set

CustomerRONNIE from SAG HARBOR NY

Igniter for oven not working

Instead of buying a new range my son said he could replace the part so I looked your company up on internet and had it shipped. Three days later I was cooking with gas again! Thanks!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

    • Flat Style Oven Igniter Kit

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver

CustomerAriel from Oxford NJ

Oven would'nt heat

First I removed the two screws that held the old element in place. I then pulled the element out about 3 inches and disconnected the two wires.
I replaced the element with the new one and tucked the connector in the insulation. Additional insulation came with the kit. I replaced the two screws that held the element in placed. Oven worked perfectly

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

    • Flat Style Oven Igniter Kit

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver

CustomerDana from Windchester IN

Oven wouldn't heat

removed 2 screws and unpluged ingiter plug ed new igniter in replaced screws and worked fine

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 1 people found this instruction helpful

Parts Used

    • Flat Style Oven Igniter Kit

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver

CustomerBarry from East Islip NY

Oven would take a very long time to warm

took out both racks and under tray at bottom of stove no tools required.
used a nut driver to remove both screws holding ignighter in place ,pulled wires up gentily and remove from standard clip by pushing ends in.
clip new ignighter in place push wires down again and install 2 screws . put all back together and it works like new .

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

    • Flat Style Oven Igniter Kit

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver

CustomerALAN from LUCK WI

Igniter would glow but stove wouldn't light

I NOTICED THAT THE IGNITOR WOULD GLOW BUT THE STOVE WOULDN'T LIGHT - I GOT THE MODEL NUMBER OF THE STOVE AND GOOGLED THE MAYTAG MODEL NUMBER. CAME UPON YOUR WEBSITE AND REALIZED THAT 94% OF THE TIME THE PROBLEM WAS THE AMPS WERE NOT ENOUGH TO LIGHT THE STOVE. I LOOKED AT ALL OF THE STORIES ON HOW EASY IT WAS TO FIX. I ORDERED THE PART AND RECEIVED IT WITHIN 3 DAYS. I OPENED THE DOOR PART WAY AND LIFTED IT STRAIGHT UP TO REMOVE IT. I PULLED OUT THE BOTTOM BROILER PLATE BY GRABBING THE BACK ON PULLING UP. I UNDSCREWED THE WING NUT OF THE FLAME BAR AND HAD EASY ACCESS TO THE IGNITER. I REMOVED THE TWO NUTS FROM THE OLD IGNITER. UNPLUGGED THE IGNITER FROM THE EASY ACCESS DOOR FROM THE BACK AND PLUGGED IN THE NEW IGNITER. REPLACED THE ACCESS DOOR AND ATTACHED THE IGNITER WITH THE TWO NUTS. PUT THE FLAME BAR BACK ON, PUT THE BROILER PLATE BACK ON, PUT THE DOOR BACK ON, PLUGGED IN THE STOVE TURNED IT ON AND SUCCESS. IT WAS SO EASY. I KNOW IN OUR AREA I WOULD HAVE PAID NEAR $200 FOR A SERVICE TECHNICIAN TO COME OUT AND DO WHAT I DID IN APPROX. 20 MINUTES AND $50 FOR THE PART. THANK YOU SO MUCH FOR YOU WEBSITE TO HELP US NOT SO TALENTED APPLIANCE REPAIR HOMEOWNERS.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 5 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:More than 2 hours

ToolsScrew drivers, Wrench set

CustomerMichael from San Diego CA

The burners inside the oven would not light

Pulled Oven from wall, disconnected gas and electric, removed bottom drawer, laid oven on its back, removed dual outlet valve ( tight space to loosen fittings, had to remove burner in oven to replace valve.) installed new valve, put teflon tape on all screw joints and tightened, Removed old Oven igniter and installed new igniter while burner was removed during the step above, reconnected all wires, connected gas, plugged in oven, pushed back into place, releveled range, Oven works great. Time does not include cleaning of range and area underneath, repainting the range top. I cleaned the range top burners also and they light much quicker now

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

    • Flat Style Oven Igniter Kit

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers, Socket set

CustomerRobert from Orange CA

Replacement of igniter

Removed two nuts and one screw to replace old igniter with new one. Replaced the nuts and screw. Turned on the oven, and it is working fine.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

    • Flat Style Oven Igniter Kit

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Socket set

CustomerBrian from Pittsburgh PA

Oven ignitor went to ignitor heaven.

The repair was real easy, other than the old bolts which just turned in the sockets when trying to get them out. It might be a good idea to provide two nuts and bolts to negate this problem. I would not mind paying a dollar or two extra for two bolts and nuts. Other than that, the instructions were clear. Product arrived on time and I would absolutely use your services again. Oven is back to working great! Thank you!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1 of 2 people found this instruction helpful

Parts Used

    • Flat Style Oven Igniter Kit

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerJohn from Racine WI

Oven did not ignite

Remove the door... it just pulls up and out... set the release tabs so you can remove the bottom plate .. pull out broiler drawer... unscrew the 2 screws on the igniter ..let that hang... remove the cover for the termination.. and unplug the old igniter... then reverse everything to put back together..

Help other customers find the most helpful instructions.

Were these instructions helpful?

< PREVIOUS 1 2 3 4 5 6 7 8 NEXT > 31-45 of 118