1528543-1-S-Frigidaire-316490001         -Oven Temperature Sensor
1528543-1-S-Frigidaire-316490001         -Oven Temperature Sensor

Oven Temperature Sensor

PartSelect Number PS1528543

This temperature sensor detects the temperature within the oven cavity.

This part works with the following brands: Frigidaire, Gibson, Kelvinator, Kenmore, Tappan & White-Westinghouse.

This part fixes the following symptoms:

  • Little or no heat when baking.
  • Oven is too hot.
  • Will not start.
  • Oven not heating evenly.
  • Compare At

    $29.08
  • You Save

    $4.85
  • Your Price

    $24.23
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.7 / 5.0, 7 reviews What's this?
1-7 of 7
 

23 of 27 people found this instruction helpful

Parts Used

  • Oven Temperature Sensor

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver

CustomerRussell from Lake Havasu AZ

Above 400 beeper went off & code numbers came up on read out

Cut off power at fuse panel. pulled stove out from wall went behind stove removed back panels in area of sensor that I could see from the front side, inside oven. Located sensor from rear & unpluged senser from wiring bundle reached inside oven & removed screws from sensor. Pulled sensor out & threaded wire through hole. Took old & new sensors to bench in shop. Plug on new not the same as old. Had to change plug Cut and stripped wires. Wire is very small, need to use a good stripper. Twisted wire together & soldered connection, used shrink wrap to insulate wire. Took part inside and reinstalled in reverse order. Used 1/4 inch nutdriver on total job start to finish.

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 9 people found this instruction helpful

Parts Used

  • Oven Temperature Sensor

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver

CustomerJoseph from Edgewater FL

No heat when turning oven on.

Started by replacing element which was clearly broken. Still no heat. So then I changed the oven sensor. Was disappointed that when I received the sensor I had to cut and splice the connector that was on it with the old one that came off the old sensor. Did that and still no heat so I had to buy a new clock/timer. Went to another store for that because of the connector not being the right type and there was no picture of the clock/timer like the other website. Overall ok, normall troubleshooting steps, just wish I didn't have to cut and splice the connector on the new sensor I purchased from here.

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 7 people found this instruction helpful

Parts Used

  • Oven Temperature Sensor

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver

CustomerMary from Castle Rock CO

Oven would kick off after preheating to temp.

Sensor very accessible. Pull off the back panel, disconect the sensor and slide out from back of oven. The original plug was cut off the sensor, as well as the new one to get the proper connector type on the new sensor. Soldered and heat shrink, and presto we had our new sensor ready for install. Install was about 5 minutes which included putting the back panel on the range. Pretty easy and works like new. Total time for project was about 20 minutes.

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 14 people found this instruction helpful

Parts Used

  • Oven Temperature Sensor

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerKathy from Greentown PA

Oven temp was not right

We removed the old part and replaced it then when warming the oven all of a sudden there was a loud noise and something went and so we called a repair man which I guess we should of done in the first place. Now he has ordered a part that cost 170 soo that is my story don't try to repair if you don't have experience.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 6 people found this instruction helpful

Parts Used

  • Oven Temperature Sensor

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsScrew drivers

CustomerJim from Kennett square PA

Not heating up properly.

What a job. Definitely should have two people do this. First, the part provided was not an exact match. I thought I was buying the same part as original. When I found it was different, there was a note that said the part may not be exact. This being said, I had to remove the wall ovens from the wall- very heavy , then had to take the back plate off, splice the wires to make the part work and then lift it up and put it back in. Next problem, its all hooked up, but still doesn't heat up correctly. Leave this to the pros.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 5 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsWrench(Adjustable)

CustomerTonya from Cokeville WY

Heating element was cracked, oven would not heat.

I used a small wrench, It was very easy to remove. once I removed the screws and disconnected the plugs from heating element then had to remove the back cover of stove so i could plug in new element. but was very easy. I am a single woman and was worried that it would be difficult to change. it only took me 20 minutes.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 6 people found this instruction helpful

Parts Used

  • Oven Temperature Sensor

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsNutdriver

Customersanta from glassboro NJ

Temp was not reading right

remove back panel took out old part splice wire replaced

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-7 of 7