1526405-1-M-Frigidaire-241684501-Drive-Blade.jpg
1526405-1-S-Frigidaire-241684501-Drive-Blade.jpg 1526405-2-S-Frigidaire-241684501-Drive-Blade.jpg 1526405-3-S-Frigidaire-241684501-Drive-Blade.jpg

Drive Blade

PartSelect Number PS1526405

The drive blade helps rotate out cubed or crushed ice.

This part works with the following brands: Frigidaire, Gibson, Kelvinator, Kenmore, Tappan & White-Westinghouse.

This part fixes the following symptoms:

  • Ice maker will not make ice.
  • Ice maker won’t dispense ice.
  • Compare At

    $32.16
  • You Save

    $5.36
  • Your Price

    $26.80
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.3 / 5.0, 6 reviews What's this?
1-6 of 6
 

16 of 25 people found this instruction helpful

Parts Used

  • Drive Blade

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Screw drivers

CustomerDavid from Ponca City OK

Ice maker would not rotate out cube or crushed ice.

1. Remove outer plastic face cover (4) screws.

2. Revove (1) U type nut keeper & (1) metal washer.

3. Remove (1) plastic nut on end of metal auger.

4. Remove inner plastic cover (4) screws and disconnect control rod. (Note postion of control rod befor disconnecting)

5. Note position and order of metal blades and plastic spacers on auger before siding off the end of auger to reposition them upon re-assembly.

6. Remove metal support panel from end of ice bucket (4) screws.

7. Remove auger & plastic cylinder from ice bucket.

8. Remove - slide drive blade off auger.

9. Drive blade replaced.

10. Re-assembled other items removed in reverse order

Help other customers find the most helpful instructions.

Were these instructions helpful?

4 of 8 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsNutdriver, Screw drivers

CustomerCalvin from Massillon OH

Rust had corroded front plate and drive blade

Installation was completed by following the online Parts diagram. Had to completely remove all parts, including the blades in ice crusher, and re-assemble. Glad the online diagram was clear and easy to read.

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsPliers, Screw drivers

CustomerDominick from Las Vegas NV

Ice not depensing, door rubbing

Remove Ice dispenser from freezer, removed all screws that hold auger & blades, by remove ring & washer. Removed blades replaced broken drive blade and re-assembled. Removed ref. door install new bearing at bottom re-installed door. Both job very easy.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 7 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Screw drivers

CustomerWayne from Westford MA

Rust on front plate and drive blade

Downloaded a schematic of the ice container. Disassembled the ice container, keeping track of which different type of screws went where. Followed the schematic to ensure proper sequence of blades and spacers. Manually rotated unit prior to installing into the freezer in case of binding. Finished.

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 9 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerWILLIAM from KERRVILLE TX

Would not dispense ice from ice tray

DID NOT REPLACE ITEMS ORDERED BUT REPAIRED ITEM (DRIVE BLADE ) AND REINSTALED REPARED PARTS UNTIL THEY FAIL COMPLETELY. i KNOW THEY WILL IT IS JUST A MATTER OF TIME.
BUT SEEING THAT I AM 72 YEARS OLD IT WAS NOT THAT DIFFICULT TO DO THE REPAIRS, JUST LIFT UP ICE BIN AND PULL OUT, THAN TAKE IT APPART REMEMBERING HOW EACH PART FACED AND IN WHAT ORDER.
THANK YOU FOR GIVING ME THE PARTS MANUAL AND NUMBERS OFF INTERNET .
SINCERELY YOURS

Help other customers find the most helpful instructions.

Were these instructions helpful?

5 of 16 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsNutdriver, Pliers, Screw drivers, Wrench(Adjustable)

CustomerJerry Baten from Pampa TX

Ice would not dispence

TOOK THE ICE STORAGE BIN OUT. TOOK THE UNIT APART,AND DISAMBLE THE AUGAR UNIT. ORDERED PARTS FROM MANUFACTURE, WHICH ARRIVED IN TWO DAYS. AS SOON AS I GOT THE PARTS, I REASSAMBLED IT. WORK PERFECT. GOOD JOB!

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-6 of 6