| |
12 of 19 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:30 - 60 mins
ToolsNutdriver, Pliers, Screw drivers
CustomerDavid from Ponca City OK
Ice maker would not rotate out cube or crushed ice.
1. Remove outer plastic face cover (4) screws.
2. Revove (1) U type nut keeper & (1) metal washer.
3. Remove (1) plastic nut on end of metal auger.
4. Remove inner plastic cover (4) screws and disconnect control rod. (Note postion of control rod befor disconnecting)
5. Note position and order of metal blades and plastic spacers on auger before siding off the end of auger to reposition them upon re-assembly.
6. Remove metal support panel from end of ice bucket (4) screws.
7. Remove auger & plastic cylinder from ice bucket.
8. Remove - slide drive blade off auger.
9. Drive blade replaced.
10. Re-assembled other items removed in reverse order
|
2 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsPliers, Screw drivers
CustomerDominick from Las Vegas NV
Ice not depensing, door rubbing
Remove Ice dispenser from freezer, removed all screws that hold auger & blades, by remove ring & washer. Removed blades replaced broken drive blade and re-assembled. Removed ref. door install new bearing at bottom re-installed door. Both job very easy.
|
2 of 5 people found this instruction helpful
Parts Used
Level of DifficultyA Bit Difficult
Time to do repair:1- 2 hours
ToolsNutdriver, Screw drivers
CustomerCalvin from Massillon OH
Rust had corroded front plate and drive blade
Installation was completed by following the online Parts diagram. Had to completely remove all parts, including the blades in ice crusher, and re-assemble. Glad the online diagram was clear and easy to read.
|
1 of 3 people found this instruction helpful
Parts Used
Level of DifficultyA Bit Difficult
Time to do repair:1- 2 hours
ToolsNutdriver, Pliers, Screw drivers
CustomerWayne from Westford MA
Rust on front plate and drive blade
Downloaded a schematic of the ice container. Disassembled the ice container, keeping track of which different type of screws went where. Followed the schematic to ensure proper sequence of blades and spacers. Manually rotated unit prior to installing into the freezer in case of binding. Finished.
|
2 of 7 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerWILLIAM from KERRVILLE TX
Would not dispense ice from ice tray
DID NOT REPLACE ITEMS ORDERED BUT REPAIRED ITEM (DRIVE BLADE ) AND REINSTALED REPARED PARTS UNTIL THEY FAIL COMPLETELY. i KNOW THEY WILL IT IS JUST A MATTER OF TIME.
BUT SEEING THAT I AM 72 YEARS OLD IT WAS NOT THAT DIFFICULT TO DO THE REPAIRS, JUST LIFT UP ICE BIN AND PULL OUT, THAN TAKE IT APPART REMEMBERING HOW EACH PART FACED AND IN WHAT ORDER.
THANK YOU FOR GIVING ME THE PARTS MANUAL AND NUMBERS OFF INTERNET .
SINCERELY YOURS
|
1 of 7 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsNutdriver, Pliers, Screw drivers, Wrench(Adjustable)
CustomerJerry Baten from Pampa TX
Ice would not dispence
TOOK THE ICE STORAGE BIN OUT. TOOK THE UNIT APART,AND DISAMBLE THE AUGAR UNIT. ORDERED PARTS FROM MANUFACTURE, WHICH ARRIVED IN TWO DAYS. AS SOON AS I GOT THE PARTS, I REASSAMBLED IT. WORK PERFECT. GOOD JOB!
|