| |
0 of 2 people found this instruction helpful
Parts Used
-
- Detergent and Rinse Dispenser with Cap
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
Tools
Customerlinda from pittsburgh PA
My soap dispenser had worn out and wouldn't stay closed anymore
Received the part quickly and installed it with no problem whatsoever. Have order parts from PartSelect before and have been very happy
|
0 of 2 people found this instruction helpful
Parts Used
-
- Detergent and Rinse Dispenser with Cap
Level of DifficultyA Bit Difficult
Time to do repair:1- 2 hours
ToolsPliers, Screw drivers
CustomerLinda from Zephyr Hills FL
Repair soap dispenser
Took off all the screws, replaced the dispenser-no problem. However, I couldn't get the top to stay in place long enough to get the screws back in. My boyfriend came over and couldn't get it together without using a longer screw in the top area. Now it works great.
The only other problem was my bank and my VISA-they both called me stating my account was being used out of the country. They issued a fraud alert at first, but I called them and told them everything was fine.
Linda
Florida
|
0 of 2 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsScrew drivers
CustomerSherry from Milton VT
Soap dispenser door broke off
First I unplugged the diswasher, than I unscrewed 4 screws on the inside of the door which pops the door off, unplug two wires, note which one goes where, unscrew 6 screws that holds dispenser in place, than reverse order to install new part. Very easy.
|
0 of 2 people found this instruction helpful
Parts Used
-
- Detergent and Rinse Dispenser with Cap
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerRobert from Greenville SC
Thanks for the help
I removed the screws from the inside of the dishwasher door to allow access to the inside of the door. Once the exterior of the door is removed the detergent dispenser is easily removed by disconnecting 6 screws and unplugging two wires from the unit. The new unit slips in and is easily reconnected. Getting the exterior of the door reinstalled is a bit challenging, but once you figure out that the exterior needs to slide up to allow the catches on the door to grab, reinstallation is easy. A second pair of hands makes this easier.
The part fits exactly with no modifications necessary.
|
0 of 2 people found this instruction helpful
Parts Used
-
- Detergent and Rinse Dispenser with Cap
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerQuan from Spingfield VA
Main soap dispenser lock is broken
Unscrew all the scews arround it. Use tape to hold the eletronic panel. Remove the metal cover.
Remove the 6 screws around the dispenser. Replace the new one. Put the metal cover back first. Put back the electronic panel at last. Done
|
0 of 3 people found this instruction helpful
Parts Used
-
- Detergent and Rinse Dispenser with Cap
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers
CustomerMichael from Alpine CA
Latch on the dispenser was broken
REMOVE THE INNER DOOR PANEL, PLASTIC, HAS 8 SCREWS, UNPLUG THE DISPENSER COMPARTMENT, AND DO THE REVERSE. THIS WAS VERY EASY. THANKS PARTSELECT!!!!!!!
|
0 of 3 people found this instruction helpful
Parts Used
-
- Detergent and Rinse Dispenser with Cap
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers
Customerstewart from holliston MA
Soap dispenser door wouldn't open fully - spring broken
I did not come with directions, but I had gotten them from the Parts Select stories from others. Removed 2 screws from inside door, dropped the front panel, removed the 6 screws holding the dispenser, unplugged the contacts, removed the dispenser and then reversed the process.
|