Heating Element Brass Nut

I looked under and found that 2 brass nuts that secured the heater element through the base housing of the dishwasher has split down each side of the nut and no longer was tight enough to keep water from leaking around either end of the heater element. I powered down the dishwasher at the circuit breaker and then reached under the dishwasher and pulled away the 2 wires that were attached to each side of the heater element. I removed the two nuts and replaced them with the parts I ordered from partselect.com. I then put the appropriate wires back at the end of the heater element and ran the dishwasher to check for leaks. No leaks... it was fixed.

Make sure power is off. Remove metal toe kick with fillips screw driver. Reach under dishwasher with 1/2" open
end wrench and completly unscrew brass nuts from element ends. Then open door and pull element ends straight up. Note: As you pull element ends up (inside washer) you are also forcing the element end wire connectors to come off underneath. The electricial connectors are very hard to get off any other way.

Wendell Hensley
Madiso0nville, Tn

Removed bottom plate and heating element brass nuts. Disconnected heating element. Connected new one then replaced brass nuts. Put bottom plate back on. Very easy.

Unplugged dishwasher, removed the 2 wires clipped to the heating element, removed both cracked nuts, replaced with new nuts from PartSelect, clipped on wires, plugged in and did a test cycle. Based upon service quote from Best Buy, I saved myself $125.00 for just the call out, not including parts and labor.

Removed lower trim covers (2 Phillips screws) disconnected power supply at breaker box. Removed wire from heating element, removed (broken) brass nut, unclipped heating element and removed. Removed flat washers and replaced with new grommets. Kind of tricky getting them in there. Also had to lube them with silicone to get the element back through. Installed new brass nuts and installed wire connectors. Reset breaker and started diswasher to verify repair. No leaks, working just fine, reinstalled lower trim covers

The nut was split down one side, so I first tried to sauder the nut back together. Saudering never goes well for me anyway, but I couldn't get a good enough seal around the nut to make it fit tightly. Then I had to cut off the clear plastic shield to get down in there, just before realizing you could just pull the white wire firmly and it would come loose from the nut. All I had to do then was unscrew the original nut, and screw on the new nut. Then, luckily I had mistakenly ordered an extra clear plastic shield and could replace the one I had previously cut. Dishwasher now runs like a charm!

I turned the power off at the circuit breaker. I then took the access panel off the dishwasher at the bottom. I pulled the wire off the connector. I used a plied to remove the broken washer and replaced with new part. I put everything back in reverse order and ran the dishwasher. I than checked for leaks over two days while the machine was running and everything was fine. Thank you Parts Select for saving me $500!

First I removed the two screws that hold the dishwasher in place, I pulled out the dishwasher and on the bottom right located the leak. The two brass nuts that hold the heating element in place. The wires had been rusted to the element so I cut the wires (and later spliced them back together) and unscrewed the brass nuts. I ordered the part after finding them very easily on partselect.com and 2 days later screwed them back on to the dishwasher. Spliced the wires back together and put the dishwasher back in place.

Easy Fix.

All you have to do power down the unit, then disconnect the power connections at the element and remove the old nuts and replace them with the new ones and tighten. Don't tighten too much, the element has a rubber seal that just needs the nut to snug it up.

I recently bought a vacation home in New Hampshire, and had a very detailed home inspection performed. The dishwasher unit was checked out to be in fine shape. Before moving in, I had all the hardwood floors refinished, including the kitchen, and everything looked great. After moving in and using the dishwasher twice, it developed a major leak coming from the bottom of the unit. "Here goes more money that I don't have, to hire an appliance repairman to fix this leak!" I decided to take the bottom kick panel off the dishwasher to see where the leak was coming from. It was coming from the the connection of the heater element at the bottom of the dishwasher. I found a brass nut had been cracked and wouldn't stay tight any more. I ordered the replacement nut from Partselect, RECEIVED IT THE NEXT DAY!!!!! using regular ground shipping, and installed the new nut using a socket set, and tested the unit. No more leaks!! Partselect saved me at least $150.00 on a service call for a $3.50 part. I'm not the handiest guy around, but even this was easy!
I also scored big points with the wife on my handyman repair! Thanks Partselect!

Greg

I removed the wires from the heating element. I removed the 2 brass nuts that had split down the side. I replaced them with 2 new brass nuts. Tightened with a wrench. I then installed the missing door spring. The repair itself took about 5 minutes.

I pulled out the dishwasher removed the two heating element insulated wires and removed both threaded brass nuts and replaced them both. Problem solved. Luckily I have a local parts and repair store with a repairman that knows every part of every appliance ever made (no kidding, I have yet to stump him with a part or question). He did not have the parts, told me to go to partselect.com order two nuts, replace them both at the same time, and fix it myself because its an easy repair and not worth paying hundreds of dollars, if you can use a wrench. He was right, and partselect.com had the right parts, at the right price, easy to find and order, and I can impress the wife with my repair skills. Thanks again!

Both heating element brass nuts had a split in them. They had fallen off the heating element and were hanging on the electrical wires. I removed the wires from the heating element and removed the brass nuts from the wires. I then screwed the new nuts on the heating element and reattached the wires. problem solved. I want to thank you for having the parts I needed as Sears had discontinued them for this Kenmore appliance.

Never worked on a dishwasher before but quickly learned that on this particular one, it's only this thin little brass nut that tightens down the element from the underside of the washer. If not tight enough, water drips right down onto the electrical connections. In this case water began to drip and the heat from the electrical current began melting a clear rubber shield thing. Luckily I was home during the cycle and figured out the problem. Great website that seems to have all necessary parts for my washer. Quick shipment!

I read the instructions that others had posted and completed the repair in less than 5 minutes!