Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS1524446
This is a strike for washing machine. This part activates the door switch.
This part works with the following brands: Frigidaire, Gibson, Kelvinator, Kenmore, Tappan & White-Westinghouse.
This part fixes the following symptoms:
Disassembled the door panel(7screws).Replaced the outer door panel keeping the existing hinge bushings in proper alignment (requires two people because of the weight of the glass door bubble). You could remove the entire door by removing the metal hinge, however, these screws would not come out for me. Replaced the striker by removing two screws.
Help other customers find the most helpful instructions.
Were these instructions helpful?
The striker is really easy to replace. Remove 2 #3 phillips screws, replace the striker part, and tighten the screws.It got more complicated when too many striker tips broke off inside the latch assembly and prevented the tip of the new striker from going inside. To get at the latch assembly, I had to remove the big rubber gasket that connects the drum to the frame of the machine. I removed this at the drum end. Big mistake! It took two of us to get the gasket back onto the drum, and I had to take the frame end of the gasket off anyway. That end is a lot easier to put back on. Anyway, I finally got to the latch assembly, which attaches to the machine with two screws. It has 3 connectors and the housing is a grey plastic clamshell that latches in 3 places. It came apart and parts came out. Jamming the latches open and very gently prying the clamshell open may let you escape the small parts barrage. Once I got everything back together, it all worked.Unfortunately, the story doesn't end there. This machine has broken 4 strikers. They break during the wash cycle. Taking a cue from a previous DIY description on this site, I took the hinge apart. It looks like there is a part missing, because there isn't anything that keeps the door aligned with the rest of the machine. The door drops down as low as it can go on the hinge pin and the plastic of the door frame rides directly on the arm of the hinge part. I've shimmed it up about 3/16" temporarily, and it seems to work, but I can't escape the idea that I shouldn't have to do this...
Replaced the old striker with the new one in about 5 minutes. Just needed a phillips screwdriver. Unbelievable how hard it was to find the part at local store...much easier to order from partselect. If I break it again, I will be all set. Part cost $7 vs repairman visit at a cost of at least $200 - - was worth the effort.
The washer door wouldn't shut. I saw the top piece of the plastic catch appeared to have a broken section. I looked online at the replacement part needed (this was the most difficult part of the process). I unscrewed the old piece and replaced it. No problems. I suspect that this is an engineered flaw with the machine to encourage more unit sales (it could be metal for instance). So fix it and feel clean!
Unscrewed two screws, replaced door striker and screwed the same two screws back in! I was done in less than 3 minutes!
door not level son slammed shut and door strike broke
2 screws and about 48 seconds of work. very easy.
Removed and replaced two screws.
I started with a Phillips head Screw driver and removed the screws from the current Door strike and replaced with a new one. To replace the Door Lock and switch assembly I had to access the right portion of the door gasket which was a little tricky, as it has a wire ring around the gasket to keep it in position. It has never been removed so it was fairly stuck so I took some pliers to pull on the gasket and ring to loosen it up. Once I got it off I was able to remove the Gasket just enough to access the electrical components to the Switch assembly. I loosened the screws on the current switch assembly using a Phillips head screw driver and removed it through the access point then unplugged the current wiring harness from the switch assembly and plugged the new switch assembly in. Then I tightened up the screws on the new switch assembly. re attaching the gasket was possibly the most time consuming as there is a metal lip on the door itself that the gasket has to wrap around in order to re attach the metal ring and hold everything in place. I took a flat head screw driver and ran it along the edges of the metal lip while pulling the gasket to secure it around the lip then I wrapped the metal around the gasket to secure it to the metal lip in the door ( Note: the metal ring has a spring that should be positioned at the bottom of the door once it's installed correctly, you will notice the gasket is shaped at the bottom to allow for the spring) Once I completed that I made sure all screws where tightened and then checked the unit to be sure it worked properly. It is working perfectly and no more error message.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.