Quick Question!

Have you ever purchased from PartSelect.com before?

1517844-2-S-GE-WH49X10042        -Agitator Coupling Kit
1517844-2-S-GE-WH49X10042        -Agitator Coupling Kit 1517844-1-S-GE-WH49X10042        -Agitator Coupling Kit 1517844-3-S-GE-WH49X10042        -Agitator Coupling Kit http://www.partselect.com/Schematics/GE/00110774i03.gif

Agitator Coupling Kit

PartSelect Number PS1517844

Washing machine agitator drive bell with bolt. It connects the transmission drive shaft to the agitator base. *NOTE: Hold down bolt not sold separately.

This part works with the following brands: GE, Hotpoint & Kenmore.

This part fixes the following symptoms:

  • Will not agitate.
  • Pumps but will not spin.
  • Noisy.
  • Shakes and moves.
  • Leaking.
  • Spins slowly.

Compare At

$11.56

You Save

$1.93

Your Price

$9.63
Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.1 / 5.0, 101 reviews What's this?
 

12 of 16 people found this instruction helpful

Parts Used:
  • Agitator Coupling Kit
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Socket set
Customer: Troy from Porter, TX

Agitator not agitating

Left up agitator, use socket set to remove agitator coupling. Then replace old agitator coupling with the new one. Tighten nut with socket set, replace agitator. Yes it is that easy.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

9 of 10 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Socket set
Customer: Ron from Benton, IL

Agitator stripped

removed the old one and replaced with new

Help other customers find the most helpful instructions.

Were these instructions helpful?   

10 of 14 people found this instruction helpful

Parts Used:
Level of Difficulty: Very Difficult
Time to do repair: 1- 2 hours
Tools: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Customer: Roger from Port Saint Lucie, FL

Water leaking through tub seal

First and foremost, the job would have taken 2 hrs instead of 8 hrs. The problem was that no one on the help instructions said that the Hub Nut had a LEFT HAND thread and suggested to just break the nut off. Well, after chiseling off most of the nut I drilled small holes through the nut and removed the nut pieces. However; I learned that I had damaged the transmission seal and had to buy a new transmission $183. Had I known this the job would have taken much less time and at a cost of about $50.
PS: The washer runs great.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

9 of 12 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Socket set
Customer: CARL from SPRING, TX

Agitator not working correctly

Removed by pulling out. Removed coupling air bell with socket and replaced. Wery well. Thnak you.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

5 of 7 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Wrench set
Customer: Anthony from Santa Clarita, CA

Agitator stripped and came off coupling

First I took off the old coupling (one screw). Put the new coupling on, lined up and snapped the new agitator onto the new coupling.
Repair took les than 5 minutes. The longest part of the whole process was lining up the agitator to the coupling.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

4 of 5 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 15 - 30 mins
Tools: Socket set
Customer: Benny from Compton, CA

The agitator was not tuning

I had help taking off the old parts,coupling was not easy. But I installed the new parts by my self and I'm 74 years had trouble getting the Agitator Coupling back on, But the straps were easy, Any way I'm back to washing again thanks a bunch

Help other customers find the most helpful instructions.

Were these instructions helpful?   

6 of 11 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Pliers
Customer: Tricia from Glen Allen, VA

Replace coupling and agitator

unscrewed the old coupling, brushed off yucky build up and replaced, ta da back to washing clothes constantly !

Help other customers find the most helpful instructions.

Were these instructions helpful?   

4 of 5 people found this instruction helpful

Parts Used:
  • Agitator Coupling Kit
Level of Difficulty: A Bit Difficult
Time to do repair: 15 - 30 mins
Tools: Wrench set
Customer: Paul from saint Clair Shores, MI

Agitator had little to no movement

I removed agitator by pulling it up until it unsnaped.

I removed the old agitator coupling by removing the bolt and pulling up while twisting it.

The new coupling looks different than the old part but fits the same.

I pressed the new coupler on to the agitator shaft, reinstalled bolt and pressed agitator on the agitator coupler until it snaped into place.

Washer runs like new!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 3 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Socket set
Customer: James from Middlesboro, KY

Agitator wobbly and noisy.

Placed a small rope under the agitator and pulled up with a sudden jerk . It popped right up and out . I removed the bolt holding the coupling .I then removed old coupling and replaced with new coupling and bolt. I then installed new agitator pushing down until it clicked into place . All done , less than 15 minutes . Thanks to others that gave their feedback so we could learn what to do .

Help other customers find the most helpful instructions.

Were these instructions helpful?   

4 of 6 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Socket set
Customer: Lester from Seymour, IN

Defective agitator

the parts you sent were same as G.E. parts and fit with very little labor on my part Just follow the directions parts snap right in place washer is good as new thanks for speedy delivery. L. Neal Seymour In.




















thanks for speedy

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 4 people found this instruction helpful

Parts Used:
  • Agitator Coupling Kit
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver
Customer: Ernest from Due West, SC

My washer stopped agitating

Our GE washer stopped agitating. We bought us a Whirlpool Cabrio washer with auto-sensing and an impeller instead of an agitator. My wife couldn't get used to washing clothes with so little water. We found out about PartSelect.com and ordered the part they indicated would probably fix our GE washer ($5.86) - the Agitator Coupling Kit. Ordered it on Friday, received it by Fed Ex the following Tuesday. It was an easy installation. Our GE is working fine. Took the Whirlpool back to the store, got our $637.00 back.I plan to use PartSelect.com again,if I need to. We don't like the new type washers as well as our 7-1/2 year old GE.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 2 people found this instruction helpful

Parts Used:
  • Agitator Coupling Kit
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Socket set
Customer: tammy from tracy, CA

The agitator was not sping

figerout how to take the old one off that was a little hard to do but did it. got the socket set to get the middle undone. clean to out and put the new one in and it works just fine and better then ever.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 2 people found this instruction helpful

Parts Used:
  • Agitator Coupling Kit
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Socket set
Customer: Catherine from Keizer, OR

Agitator spun but would not agitate

Replaced the plastic agitator coupler

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 2 people found this instruction helpful

Parts Used:
  • Agitator Coupling Kit
Level of Difficulty: Really Easy
Time to do repair: 1- 2 hours
Tools: Socket set
Customer: David from Syracuse, IN

Would not agitate

Reading all the other stories helped me get started. One tip I want to share is when removing the old coupler, I held on to a pulley puller by hand. I hooked the jaws underneath; while I pulled up on it, I would tap with a hammer on either side of the old coupler. This gave me the leverage needed to make it pop right off.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 2 people found this instruction helpful

Parts Used:
  • Agitator Coupling Kit
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Socket set
Customer: Christopher from Holly Springs, NC

Washing machine would fill, spin, and drain, but would not agitate

After doing some troubleshooting, I found that the Air Bell was stripped inside.

First I removed the agitator by firmly pulling it straight up. Then I removed the bolt holding the air bell (agitator coupling) with a ratchet. Then came the hard part. The air bell (agitator coupling) was stuck on the shaft and would not come off. I used rope to lasso under the coupling and tied it to a 2x4 for leverage and eventually wrestled it off by using an upward jolting motion time and time again. Spraying WD-40 in the coupling seemed to help loosen it up.

Prior to installation, I cleaned the grooves of the shaft by scraping them out with a flat tip screw driver. Installed the new coupling by tapping it down with a hammer until it was seated firmly and locked it down with the new bolt. Aligned the agitator and slid it down until it latched. Done!

Help other customers find the most helpful instructions.

Were these instructions helpful?