1490170-1-S-Whirlpool-W10072840         -Inner Cap Seal
1490170-1-S-Whirlpool-W10072840         -Inner Cap Seal 1490170-2-S-Whirlpool-W10072840         -Inner Cap Seal http://www.partselect.com/Schematics/Maytag/TEBJZIYW.gif

Inner Cap Seal

PartSelect Number PS1490170

Also known as an O-Ring.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Will not agitate.
  • Leaking.
  • Noisy.
  • Shakes and moves.
  • Pumps but will not spin.
  • Compare At

    $5.17
  • You Save

    $.86
  • Your Price

    $4.31
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.1 / 5.0, 70 reviews What's this?
1-5 of 70
 

494 of 501 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Socket set
Customer: Lennis from Jacksonville, NC

Would not agita.

It was a blessing that I ordered the kit, because I thought it only needed the rubber seal and the four dogs. But because the seal and dogs cost less than the shipping I decided to order the kit and its good I did because the nochage on the basket sleeve was broke off. The blessing is that the sleeve was in the kit, sp it took 5 sec to slip it on along with the rest of the kit, and after about 15 min my wife was back to work. Thanks for saving me time and money without this web site I would have bought another brand new washer, thanks. Lennis from NC.

Help other customers find the most helpful instructions.

Were these instructions helpful?

344 of 398 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 1- 2 hours
Tools: Nutdriver, Pliers, Screw drivers, Socket set
Customer: Dexter from Milwaukie, OR

Washer made a loud banging noise at end of spin cycle, leaked water and agitator seemed loose

After entering the model number of your appliance you will be taken to a page where all of the parts are displayed by sections. On that page about in the middle there is a heading called "Find Part By Symptom." I figured out from there which symptom the washer had and read what other people were saying and how they made the repairs. Basically I had three problem areas, Noise, Leaking and a problem with the agitator. I focused on the loud noise first and decided I needed to replace the clutch/brake assemblies. I found the clutch parts page and on that page there was a video on how to make this repair. This video is all you need to gain access to all moving parts located under the cabinet. Which ever part you are replacing, I recommend watching this video! After removing the console, back panel and cabinet then laying the machine on its back just as seen on the video, I had access to the water pump, motor, transmission and related clutch/brake parts. As it turned out I did not need the clutch/brake assembly but as a precaution and because the parts were cheap, I replaced the motor coupling, water pump and tub wear pads. I decided to replace the agitator assembly because of several worn parts associated with the dog ears/drive shaft ETC. I put the machine back upright and took off the top cap on the agitator, then there is an inner cap with seal that gives access to the 7/16" bolt you must remove to remove the agitator. However once the agitator was removed I noticed metal shavings and play in the shaft. I used a spanner wrench to remove the spanner nut. I removed the Plastic Tub Ring (has several clips around the outer tub), then removed the inner washer tub to replace the Drive Block. Replacing the Drive Block stopped the loud noise at the end of the spin cycle. Now just reverse the order to put the machine back together and your done. For my situation it was best to take the machine apart and decide which parts I needed before ordering to minimize errors. These machines are made very cheaply and are designed to brake at some point in time and it is very easy to determine which parts are worn because most are made of plastic. In this process I also noticed where my leaks (did I say Leaks) were coming from. There were two hose clamps installed improperly from the factory, so check all clamps, hoses ETC. and you should be good to go.

Help other customers find the most helpful instructions.

Were these instructions helpful?

136 of 154 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Pliers, Socket set
Customer: Michael from Claremont, CA

Top part of agitator (auger) was not turning

Using kit 285587 was straight forward. Removed fabric softener dispenser & sealing cap. It took more time to find the socket set (needed a 7/16 socket) with a long driver (10 inch) than to unscrew & remove the auger & agitator.
Cleaned up the bowl whilst it was apart (good buildup of junk under the agitator). Replaced agitator, new thrust washer to find that grease should be applied but isn't included in kit (get part not 350849). Grrr.... Applied new auger, cam, dogs and holder. (No instructions in kit for assembling cam, dogs & holder, but you can work it out ok). Applied new bolt & washer, new seal on cap. Installed fabric softener. Could have been a 15 minute job but peace and quiet in the garage makes it worthy of taking longer ;-)

Help other customers find the most helpful instructions.

Were these instructions helpful?

39 of 46 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Pliers, Screw drivers
Customer: mary from Wilmington, NC

Lid switch broke and washer would not drain or spin

I read the repair suggestions from Paul and Karen. I was amazed at how easy it really was. I have never fixed something like that before and my husband was not home to do it so I just read the directions for repair on your partselect site. I printed off the directions that another person wrote and followed them as to how to take off the control panel. ONce that was off, the rest was easy. I numbered each screw and hole so it would be easy to put back together but really wasn't that necessary. It really took less than an hour, I am glad I didn't pay someone to do it! It's was extremely helpful to have the directions on your site that told how to take the control panel off.

As for the O ring replacement..that was less than five minutes...just take the top part off and pull the other part out and replace the ring. Anyone can do that. No tools.

Help other customers find the most helpful instructions.

Were these instructions helpful?

25 of 29 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers, Socket set, Wrench set
Customer: Richard from Houston, TX

Agitator would not spin

replaced the agitator cogs, bearing and the O-Ring. I looked all over Houston for these part, but found them on PartSelect. Had them in about 3 days. The repair only took about 30 minutes.

I saved a bunch of money!!
Thanks.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 70