| |
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyA Bit Difficult
Time to do repair:30 - 60 mins
ToolsScrew drivers, Socket set, Wrench set
CustomerKeith from Mount Vernon WA
Timing tabs securing the agitator center
There are 4 tabs that come from the main agitator body through the center & lock into the centerpiece that holds the directional cogs. They have a tab similar to a cable tie that can only be put on once. They need to be clipped before it will dissassemble & reassembly is difficult because they need to be timed to reattach the round center cog plate. Maybe cut off 2 of them & taper the other 2 them for easier reassembly.
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyA Bit Difficult
Time to do repair:15 - 30 mins
ToolsPliers, Socket set
CustomerDavid from Warren MI
Top of agitator was not working
I basically followed the video that was available on Partselect.
I had trouble getting the top of the agitator separated from the lower but I used a length of 2x4 and gently tapped this with a hammer (so I wasn't hitting the plastic directly with the hammer, never a good idea). I few taps around the perimeter of the upper agitator and it came apart. The rest was quite easy. I replaced the seal since it looked pretty worn when I first removed the inner cap.
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsSocket set
CustomerLennis from Jacksonville NC
Would not agita.
It was a blessing that I ordered the kit, because I thought it only needed the rubber seal and the four dogs. But because the seal and dogs cost less than the shipping I decided to order the kit and its good I did because the nochage on the basket sleeve was broke off. The blessing is that the sleeve was in the kit, sp it took 5 sec to slip it on along with the rest of the kit, and after about 15 min my wife was back to work. Thanks for saving me time and money without this web site I would have bought another brand new washer, thanks. Lennis from NC.
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsSocket set
CustomerMerlin from Bath ME
Washer would not agitate
Followed the directions provided. Took less than 15 minutes and the washer works like new.
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsNutdriver
CustomerDennis from Spring Grove IL
Agitator was free wheeling
repair was really simple. If you can get it apart, you can fix it. the parts fit perfectly.
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsWrench set
CustomerROBBIE from BELLEFONTE PA
Agitator did not spin
I took the liquid detergent cup off.
Took the inner cap out.
Removed the 7/16in. bolt out with a socket and a ratchet with an extension.
I cleaned all parts.
Replaced the parts.
Works Great.
|
2 of 4 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsSocket set
CustomerThomas from Omaha NE
Top of agitator stopped working.
Removed nut holding the agitator in and replaced. Quick and easy.
Was easy to order and was here in 3 days. Faster than the local part dealer could get it to me.
Will use again if needed.
|
2 of 4 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsSocket set
CustomerBRUCE from MIDDLETOWN OH
The adgitator was not moving as it should have.
Pulled off the cover on the adgitator then removed the cap inside the adgitator and the one 7/16 bolt holding on the adgitator. Pulled the adgitator top off the base and removed the drive section with the 4 fingers that engaged with the adgitator. Installed the new assembly, put the bolt back in and I was done.
My wifes 19 year old Kitchenaid washer now works like new and all of that for less then $20.00
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsSocket set
Customerroger from Delanco NJ
Upper agitator not spinning
After removing the pressed in cap inside the agitator i removed it from the machine with a socket wrench. Then it did not take long to figure out that the two peices snapped apart. then one look at the cogs (referred to as dog ears) i knew they where stripped and where the problem. Icanceled the service call and order the parts myself from this site. So it was very easy and i'm not sure how much money i saved but the bragging rights went along way with the wife, Thanks.
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:Less than 15 mins
ToolsSocket set
CustomerMichael from Watson AR
Worn cogs, machine would not agitate.
Well, I took out the worn parts, replaced them with new ones, end of problems. except that I did not see in the parts book where the new agit came with new cogs . So, I wound up with an extra set of cogs (at my cost). Gotta say one thing though, the service was good and fast, even though it was during christmas holidays. Thanks.
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:Less than 15 mins
ToolsNutdriver
CustomerTanya from Garrettsville OH
Agitator not working (again)
The dogs (directional cogs) cause the upper portion of the agitator to turn in one direction only. The clothes don't get clean unless this happens.
The material the dogs are made of wears out in a few months of use.
I buy 4 packages of them at once, every few years.
Pull off the inner cap, unscrew the bolt, remove the old cogs, put in the new ones, reverse the disassembly process and away we go.
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyReally easy
Time to do repair:15 - 30 mins
ToolsScrew drivers, Socket set
CustomerCarolyn from Jackson MS
Upper agitator not moving
Repair very simple, removed the top cap and lower cap, unscrewed the retaning nut. Removed the agitator. The directions supplied with the kit worked great. Reinstalled and worked like new.
|
1 of 1 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:15 - 30 mins
ToolsSocket set
CustomerBob from WALPOLE MA
Agitator noisy-slipping
using a schematic from this web site and reading other stories about this problem- I removed the upper agitator assembly-once I pulled off the fabric softner assembly-used a socket with a 8" extension to remove the bolt inside the top of the agitator-pulled off thje upper assembly-spent most of my time cleaning all the surfaces found the 4 clutch dogs damaged- placed the order for the repair kit -2 days later the parts arrived with instructuions making installation easy.
|
2 of 4 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:Less than 15 mins
ToolsNutdriver
CustomerShawn from Trinidad CA
Agitator broke
After recieving parts, I installed them easily. After the repair was complete, I noticed some screws/bolts under machine. I added some loctite to bolts and reinstalled into transmission. machine runs like new! Thanks PartSelect!
|
1 of 2 people found this instruction helpful
Parts Used
Level of DifficultyEasy
Time to do repair:Less than 15 mins
ToolsSocket set
CustomerRobert from Millsboro DE
Stop agitator not turning
popped off the softener cap, removed inner seal cap, removed bolt holding the top agitator and removed top agitator by pulling up. Removed the ring holding the dogs in place. Replaced the dogs and slipped it all back together
|