1489462-1-S-Whirlpool-W10001130         -Foot, Front - Single
1489462-1-S-Whirlpool-W10001130         -Foot, Front - Single 1489462-2-S-Whirlpool-W10001130         -Foot, Front - Single 1489462-3-S-Whirlpool-W10001130         -Foot, Front - Single

Foot, Front - Single

PartSelect Number PS1489462

Sold Individually.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Shakes and moves.
  • Compare At

    $2.34
  • You Save

    $.39
  • Your Price

    $1.95
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 2.7 / 5.0, 5 reviews What's this?
1-5 of 5
 

27 of 37 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:More than 2 hours

ToolsNutdriver, Pliers, Screw drivers, Socket set, Wrench set

CustomerPaddy from Ferndale WA

Bearings went out in the drum.

purchased the bearings at Napa auto parts for 16$. Over all it was a little difficult to get the bearings out and back in. Used a brass drift to drive them out and to seat them back in..

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 6 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Screw drivers

CustomerErnest from Midlothian VA

No agitation, no spin, pump ok

I was familiar with the Kenmore / Whirlpool direct drive mechanism but at first I could not determine how to release the console. I finally found the end cap trim pieces would pop off revealing the 2 screws that hold the console in place. After removing them the console flips up and over the backboard. I then removed the 2 clips that hold the cabinet to the backboard, unpluged the lid switch connector and then tipped the entire cabinet forward and off the frame. This gives you access to the entire washing machine mechanism.
Next I released the 2 metal clips that hold the pump on and push it out of the way leaving the hoses connected. Next I released the 2 clips that hold the pump on, these clips also have a screw to secure them. I was then able to set the motor to the side without removing any wires.
The coupling parts had broken and were already off of the motor shaft and the input drive shaft of the transmission. I put the new drive parts on and had to tap them down untill they were flush with the end of the shafts. I then put the rubber coupling on the transmission drive end and aligned the motor drive to mate into the other holes in the coupling as I put the two back together. I then re attached the 2 motor clips with screws and reinstalled the pump with it's clips. I then reinstalled the cabinet onto the frame and replaced the cabinet clips. I then plugged in the lid switch connector and flipped the console back over and screwed it down. I then reinstalled the trim caps that had me stumped to begin with. The unit tested out OK.

Help other customers find the most helpful instructions.

Were these instructions helpful?

7 of 19 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers, Screw drivers, Wrench(Adjustable)

CustomerRandy from Atlanta GA

Broken water inlet syphon combined with missing feet was causing water to spill out of the washer

I removed the back of the washer, removed the old water inlet syphon, replaced it with the new one, and, with some difficulty, replaced the back of the washer, reattaching all of the parts to it.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 2 people found this instruction helpful

Parts Used

  • Foot, Front - Single

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsWrench(Adjustable)

CustomerRick from Lennon MI

Bought a washer without front leveling feet

The repair was simple as you can imagine. Thought I could buy these legs at any big box store or at least at the local hardware store. No such luck. Partselect had the right product---easy to order and easy to install. Things around here are great.

Help other customers find the most helpful instructions.

Were these instructions helpful?

6 of 155 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:30 - 60 mins

ToolsNutdriver, Pliers, Screw drivers, Wrench set

Customerkaine from butler PA

Washer not rotating

Washer not rotating, removed the control head and back cover. Then removed body housing around tube to get to the bottom. had to replace coupling on motor then removed the agitator tower and replaced the Parts for the tower agitator. unit is 16 years young and still looks and runs new, put a total of 55 dollars into repair and it should be good for a long time. This is with a family of five. Washing 2 loads everyday.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 5