http://www.partselect.com/Schematics/Whirlpool/Whirlpool_Thumb/0XW0IVKY.gif
See part 6 in the diagram

Transmission Gasket

PartSelect Number PS1488426

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

  • Compare At

    $5.35
  • You Save

    $.89
  • Your Price

    $4.46
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.8 / 5.0, 6 reviews What's this?
1-6 of 6
 

7 of 10 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerStephen from Colorado Springs CO

Worm gear stripped.

Removed mixer motor housing by removing 5 obvious screws.
Removed plastic transmission cover by removing 4 obvious screws.
Down load parts exploded drawing from PartSelect.com
Found the worn part by the shiny teeth on the large gear.
Found the large worm gear on the drawing and ordered the gear, and associated bearings. Did not need the seal.
Removed worn part, assembled new gear and beargings in same manner as the worn part, and placed new part in mixer.
Replaced transmission cover gasket.
Repacked grease from transmission cover onto the new gear.
Replaced transmission cover (4 screws).
Replaced mixer motor housing (4 screws).
Replaced mixer trim band around the motor houseing joing. (1 screw).
Plugged it and and it works, good as new.

Help other customers find the most helpful instructions.

Were these instructions helpful?

9 of 20 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

Customerjoe from monaca PA

Mixer does not mix 4 cups of flour with 6 eggs very easily

sat on the kitchen table and with a screwdriver started to disasemble the mixer,hardest part was taking snap ring off (easy after you buy snap ring pliers)as gears were lifted off noticeable wearing was present on all parts. the bearing housing on the gearcase was broken lose, the only major expense. the other parts are not expensive so i decided to renew all parts. glad i did felt proud of myself when job was done. would do it again Joe

Help other customers find the most helpful instructions.

Were these instructions helpful?

3 of 5 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers

CustomerGary from Hamburg MN

Gears and bearing failure

inspected and replaced worn components

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 3 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:30 - 60 mins

ToolsScrew drivers

Customerconradt from el paso TX

Last repairperson broke the top cover of the gearcase ; still need this part .

Easy ; remove belt ( 1 screw ) remove cover , and there is the complete drive . I still need the top plastic cover which is cracked and broken where the bolts go through . Please quote this part .Conradt

Help other customers find the most helpful instructions.

Were these instructions helpful?

2 of 5 people found this instruction helpful

Parts Used

Level of DifficultyEasy

Time to do repair:30 - 60 mins

ToolsScrew drivers

Customerjay from mifflintown PA

Mixer blade stopped moving. Motor was working.

Removed the top housing.
Visual inspection revealed a cracked gear housing.
Removed the 4 screws to remove the housing.
Removed the gear retaining clip and inspected the gears and pin.
The housing was the only problem.
Noticed the plastic housing locating pins were missing and were stuck in the bottom aluminum housing pin receptacles. Carefully drilled out and cleaned debris.
Installed the new gear housing with gasket.
Tested the machine then replaced the top housing.

Help other customers find the most helpful instructions.

Were these instructions helpful?

0 of 1 people found this instruction helpful

Parts Used

Level of DifficultyReally easy

Time to do repair:Less than 15 mins

ToolsScrew drivers

CustomerMary from York PA

Grinding sound

Replaced cracked plastic gearcase/transmission with new medal one and replaced hub bevel gear attachment, bevel gear and gasket.

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-6 of 6