1484648-1-S-Whirlpool-2315576           -Single Water Inlet Valve - 120V 60Hz 35W
1484648-1-S-Whirlpool-2315576           -Single Water Inlet Valve - 120V 60Hz 35W 1484648-2-S-Whirlpool-2315576           -Single Water Inlet Valve - 120V 60Hz 35W 1484648-3-S-Whirlpool-2315576           -Single Water Inlet Valve - 120V 60Hz 35W http://www.partselect.com/Schematics/Maytag/Maytag_Thumb/DKAQAI3W.gif

Single Water Inlet Valve - 120V 60Hz 35W

PartSelect Number PS1484648

Also known as a Water Solenoid Valve. The water inlet valve is a solenoid-operated switch that, when activated, releases water from the supply line to the water valve and into the compact icemaker mold.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Ice maker not making ice.
  • Leaking.
  • Ice maker won’t dispense ice.
  • Not dispensing water.
  • Compare At

    $56.59
  • You Save

    $9.43
  • Your Price

    $47.16
In Stock
Order within the next 9 hrs and your part ships today!
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.9 / 5.0, 10 reviews What's this?
1-5 of 10
 

53 of 69 people found this instruction helpful

Parts Used

  • Single Water Inlet Valve - 120V 60Hz 35W

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Wrench set

CustomerRobert from Abingdon, MD

No water feed to icemaker

To troubleshoot - Check water supply to valve. It f that's good - remove back plate, remove water valve reconnect inlet line, disconnect electrical connector, place valve over a pan with outlet fitting disconnected, temporarily connect 110 VAC with clipleads to water valve solenoid. No water flow means valve is not opening. To install new valve, connect outlet line, and wiring connector, then insert in cabinet and install 2 screws, reinstall back plate, connect water inlet line.

Help other customers find the most helpful instructions.

Were these instructions helpful?

31 of 32 people found this instruction helpful

Parts Used

  • Single Water Inlet Valve - 120V 60Hz 35W

Level of DifficultyEasy

Time to do repair:15 - 30 mins

ToolsNutdriver, Wrench (Adjustable)

CustomerRobert from Pittsboro, NC

Ice maker wasn't making ice cubes

I first poured water into the ice maker itself and it made ice, so knew the ice maker itself was working ok. Turned the water valve at the wall off, removed the inlet valve from the back of the fridge with a nut driver, disconnected the solenoid wires and disconnected the water supply line entering the inlet valve and turned the water supply back on and found that the water was flowing ok out of the supply line. Reconnected the water line to the inlet valve and disconnected the water line going from the inlet valve to the ice maker and reconnected the wires to the solenoid on the inlet valve and found no water going through and so determined that the inlet valve/solenoid was faulty and easily replaced it. Note that an ohmeter check said the solenoid was ok, so it could have been that the filter screen inside the inlet valve was blocked. It's a sealed unit, so there was no way to take the screen out to check.

Help other customers find the most helpful instructions.

Were these instructions helpful?

13 of 19 people found this instruction helpful

Parts Used

  • Single Water Inlet Valve - 120V 60Hz 35W

Level of DifficultyReally Easy

Time to do repair:1- 2 hours

ToolsNutdriver, Pliers

CustomerRussell E from Rome, PA

Water was overflowing into ice bin.

First I ascertained that valve was faulty. Ordered replacement and installed without issue. Water now overflowed only during fill and found that filler neck had ice in it as a result of initial leakage. Defrosted with a hair dryer, removed ice plug and it now works as advertised.

Help other customers find the most helpful instructions.

Were these instructions helpful?

12 of 16 people found this instruction helpful

Parts Used

  • Single Water Inlet Valve - 120V 60Hz 35W

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

ToolsNutdriver, Wrench (Adjustable)

CustomerWilliam from Springville, AL

Ice maker would not fill with water

Turn off the water supply.
Remove the two screws with a nut driver.
Disconnect the electrical connector.
Disconnect the water supply lines from the old valve.
Reconnect the water supply lines to the new valve.
(be sure to push the water line into the quick connect securely)
Reconnect the electrical connector.
Re-install the valve with the two screws.
Turn water supply on.

Help other customers find the most helpful instructions.

Were these instructions helpful?

12 of 17 people found this instruction helpful

Parts Used

  • Single Water Inlet Valve - 120V 60Hz 35W

Level of DifficultyA Bit Difficult

Time to do repair:15 - 30 mins

ToolsNutdriver, Wrench (Adjustable)

CustomerSteven S. from Kerrville, TX

Leaking water inlet valve

This would have been a less-than-5-minute repair except for one item. The water intake nossle was 180 degrees from the original part. As a result, the copper water inlet tube would not fit in the old space and still allow me to reattach the valve to the freezer chassie. I ended up leaving the valve hanging loose under the freezer. I spent most of my time trying to fit the valve into the old space.

Unplug freezer. Disconnect electrical connections (pull apart). Remove one screw holding the valve to the chassie. disconnect water inlet pipe and water outlet pipe from old valve.

Reconnect electrical connection to new valve. Reconnect in and out water hoses. Reconnect valve to chassie. Plug freezer back in. Finished

Everything works just fine !

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 10