Quick Question!

Have you ever purchased from PartSelect.com before?

1483583-1-S-GE-WR62X10055        -Dispenser Door Solenoid Assembly
1483583-1-S-GE-WR62X10055        -Dispenser Door Solenoid Assembly 1483583-2-S-GE-WR62X10055        -Dispenser Door Solenoid Assembly 1483583-3-S-GE-WR62X10055        -Dispenser Door Solenoid Assembly http://www.partselect.com/Schematics/GE/00120714i01.gif

Dispenser Door Solenoid Assembly

PartSelect Number PS1483583

This part is a possible option when ice door won't open or shut properly or when water is not dispensing.

This part works with the following brands: General Electric, Hotpoint.

This part works with the following products: Refrigerator.

This part fixes the following symptoms:

  • Ice maker won’t dispense ice.
  • Not dispensing water.
  • Door Sweating.
  • Door won’t open or close.
  • Leaking.
  • Freezer section too warm.
  • Ice maker not making ice.
  • Frost buildup.
  • Freezer not defrosting.

Compare At

$49.33

You Save

$8.22

Your Price

$41.11
Get this part fast. Average delivery time via standard shipping: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.8 / 5.0, 90 reviews What's this?
 

1 of 1 people found this instruction helpful

Parts Used:
  • Dispenser Door Solenoid Assembly
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: NICK from COCOA bEACH, FL

Ice dispenser door will not shut completely

I removed the door cover plate and disconnected the circuit board, then four screws. The part was corroded in place. Upon removing three screws and cleaning the surface, the new part was an exact fit, replaced it and everything works like new.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Dispenser Door Solenoid Assembly
Level of Difficulty: A Bit Difficult
Time to do repair: 1- 2 hours
Tools: Nutdriver, Screw drivers, Socket set
Customer: Stephen from Richmond, VA

Ice wouldn't come out of door. It backed up in door

I followed the instructions on a posted desctiption. It workded perfectly. Replacing the inner door panel was not as difficult as described. Just start the process with the screws in the middle of the door. Those two screw holes were not slots. All of the remaining screw holes had slots. I installed all of the door screws before tightening any. I workded right the first time.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Dispenser Door Solenoid Assembly
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Screw drivers
Customer: robert from kansas city, MO

Ice dispencer door will not closeremoved hte control panel

removed the control panel ,using a paper clip, removed five screws, disconected wire connector, and removed the solenoid. reversed procedure to reassemble. ordered the part one day and received it the next day. Thank you for the prompt response.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Dispenser Door Solenoid Assembly
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: jeff from stillwater, OK

Solenoid quit working

repair was easy, just removed control panel and removed screws from solenoid, switched out with new, was done in minutes

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Dispenser Door Solenoid Assembly
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Richard from Fishers, IN

Ice maker door fails to close

1. Remove outside panel (snaps off)
2. Remove Control panel 4 screws
3. Remove Solenoid by taking out 2 bottom screws
4. Remove solenoid weight from crank lever
5. Place new solenoid weight from crank lever
6. Insert weight in solenoid
7. Place back 2 bottom screws solenoid
8. Place back Control panel screws
9. Snap back into place outside panel

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 4 people found this instruction helpful

Parts Used:
  • Dispenser Door Solenoid Assembly
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers, Socket set
Customer: DALE from OLATHE, KS

Ice machine trap door not opening or closing

Fairly simple fix. You must first uplug refrigerator, then take off the inside freeze door panel, approx. 25 screws. Then you must take out the trap door assembly approx. 6 six screws. Pop off the LED panel, requires the use of a flat blade screw driver to pop it off. Remove solenold by removing 3 screws, replace with new solenold.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
  • Dispenser Door Solenoid Assembly
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Colin from Saint Helena Island, SC

Bad solenoid not closing ice dispenser door

Followed the on line video. Clear, concise & easy. Thanks.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
  • Dispenser Door Solenoid Assembly
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Howard from Shelby Twp., MI

Flap to ice dispenser would not close

I followed the video provided, and followed the advice of bill from cleveland hts. ohio, and did not have to remove the trim to access everything. The video made it so simple, a monkey could have learned how in 5 minutes. Thank you very much for all the help on this website. I will recommend it to all.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Pliers, Screw drivers
Customer: Mark from Elk Grove Vill, IL

Ice dispenser door sticking open

Removed access panel on freezer door, removed circuit board, removed and replaced solenoid, reinstalled previously removed parts

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Thomas from Lake George, NY

The ice dispenser door would not open or close.

It was actually very easy. You simply remove the display cover (you just want to be careful removing the display cover so as not to damage the lower part which secures it to the door), unplug the wires, remove the inner cover (4 screws) to gain access to the solenoid. Remove the 4 screws on the solenoid replace with the new one, put the inner cover back in with the 4 screws that were previously removed, plug the wires back in and then replace the display cover.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 5 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Pliers, Screw drivers
Customer: George from Brooklyn, NY

Replaced solenoid on ice maker

I never would have attempted the repair as all my research indicated that I would have to take the stainless steel door off to replace the ice maker solenoid that shuts the ice chute door. But on your site someone (bless them)wrote that you could get at the solenoid by popping off the electronic selector panel. They are on the underside of the dispenser and not at all visible. And your video helped too. Thanks.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
  • Dispenser Door Solenoid Assembly
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Resa from Potomac Falls, VA

Flap on ice maker not closing

I searched the site, found the part - solenoid, watched the "how to" video and the repair was a snap. Saved myself tons of money versus having a repair person come over. I do have an older model and needed to prop the front cover panel off with a screwdriver (just under the covering) saw this on a posting from another individual, thanks for the heads up.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
  • Dispenser Door Solenoid Assembly
Level of Difficulty: Easy
Time to do repair: 1- 2 hours
Tools: Screw drivers
Customer: Julia from Clearwater Beach, FL

Frost formed around ice maker dispensser due to the flap not closing properly, the solenoid needed replacing

no instructions came with the part so I wrote for help from your techs. They were able to tell me how to access the solenoid. From there I was able to figure the rest out. I had to remove the trim, electrical board, flap, springs and arm to reach the screws necessary to remove the solenoid. I removed some of the corrosion with a baking soda paste so I could remove the screws. I carefully noted each step and position of the parts I removed and reversed the process to put things back after replacing the solenoid.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 5 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Victor from Houston, TX

The compartment behind control panel with snow

This time I did not make repair. I have purchased only to have spare parts. I have changed this parts recentely and I think this parts are not strong enough to work more than two or three years.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
  • Dispenser Door Solenoid Assembly
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: james from apex, NC

Replaced the ice flap solenoid

I followed the instructions posted by previous custmers and they were accurate and simple

Help other customers find the most helpful instructions.

Were these instructions helpful?