Quick Question!

Have you ever purchased from PartSelect.com before?

1482372-1-S-GE-WH12X10334        -Lid Switch with Wire Harness
1482372-1-S-GE-WH12X10334        -Lid Switch with Wire Harness http://www.partselect.com/Schematics/GE/00122750i02.gif

Lid Switch with Wire Harness

PartSelect Number PS1482372

The pin on the lid pushes on the lever of the lid switch to tell the machine that the lid is closed.

This part works with the following brands: GE, Hotpoint & Kenmore.

This part fixes the following symptoms:

  • Pumps but will not spin.
  • Will not agitate.
  • Will Not Start.

Compare At

$22.19

You Save

$3.70

Your Price

$18.49
Get this part fast. Average delivery time via standard shipping: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.9 / 5.0, 4 reviews What's this?
1-4 of 4
 

196 of 242 people found this instruction helpful

Parts Used:
  • Lid Switch with Wire Harness
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools:
Customer: Brian from Millerplace, NY

Washing machine would not go through all cycles or agitate

After removing frt panel which prys off I checked for anything obvious like a loose belt. Then I jiggled the magnet switch located on the inside of the loading cover. I saw the machine start agitating the it stopped again when I stopped touching it. I ordered the new part and spliced it in with the wire crip tool. Now the machine is A ok.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Lid Switch with Wire Harness
Level of Difficulty: Very Easy
Time to do repair: 15 - 30 mins
Tools: Pliers
Customer: Nelson from LARGO, FL

Machine will do everything and stop at the last spin, will not spin at the end.

I researched what could be the problem in the internet and follow the instructions from a GE technician, I chose the problem from a list and followed the video the technician played on how to do it yourself. This time was the lid switch which is found visible under the lid opening usually right middle flush with the opening. When I got the new lid, only the switch gets bad so I cut the cable enough to replace the old one, pulled out and cut and connected the new one. If there is not enough cable use the spatula to push the clips on the front panel on the top both side about 5 inches from the corner and pull panel out front and now you can see the wires better and make the connection.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Lid Switch with Wire Harness
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools:
Customer: Mark from Duanesburg, NY

Washer lid sensor stopped working, thus, would not spin, thinking lid was open

This was easy and took maybe a half-hour. The harder part was pulling the front panel off (up) to access the insides. Simply snipped the wire to the old sensor and spliced the new wire and inserted the new sensor. Worked perfectly and saved me $400? on a new washer! (Cover panel is slightly bent, did not re-snap in, so it's loose; I don't care about the looks, so I will screw metal screws using a hinge to close it.)

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
  • Lid Switch with Wire Harness
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Pliers, Screw drivers
Customer: MAUREEN from ABINGTON, MA

Washer would not spin .

First I googled the problem. Then ordered your part, from specs on your website. Went to Lowes and bout butt splicers. Then when I got email that it shipped I watched the video attached. Awesome. Very proud as I am a woman. Video was excellent. Thank you, Maureen

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-4 of 4