1482140-3-S-GE-WE18M28           -Lint Filter and Frame
1482140-3-S-GE-WE18M28           -Lint Filter and Frame 1482140-1-S-GE-WE18M28           -Lint Filter and Frame 1482140-2-S-GE-WE18M28           -Lint Filter and Frame http://www.partselect.com/Schematics/GE/GE_Thumb/00002276i02.gif

Lint Filter and Frame

PartSelect Number PS1482140

This filter collects lint as it passes through the dryer vent.

This part works with the following brands: GE, Hotpoint & Kenmore.

This part fixes the following symptoms:

  • Takes too long to dry.
  • Noisy.
  • No heat or not enough heat.
  • Too hot.
  • Marks left on clothes.
  • Compare At

    $38.16
  • You Save

    $6.36
  • Your Price

    $31.80
In Stock
Fast Shipping Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.2 / 5.0, 14 reviews What's this?
1-5 of 14
 

197 of 306 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:More than 2 hours

ToolsScrew drivers, Socket set

CustomerEdwin from Seattle, WA

Dryer making grinding noises

We live in a Condominium, space is tight especially in the Utility room where the washer/dryer are located. Turned dryer breaker off at the electical panel.
Removed the top cover and front assembly w/door and front drum support, right where the unit was located. Had to gain rear access to loosen drum drive belt so undid the dryer vent hose to floor connection through a front acess hole. Moved the unit out to the breakfast nook as well as disconnecting the power cable from the wall socket. Removed the rear access panel covers and unhooked the drive belt. At the front removed the top screws off the lower cross member to allow spreading of the side covers to allow the removal of the drum. Removed drum and found the bearing bushing gone, reduced to powder.
Using the supplied instuction sheet, replaced the rear bearing assembly, replaced the drum after vacumming the whole interior and started the reassembly of the unit using the new belt and moved the unit back into place. Reconnected the power cable and dryer vent then lastly replaced the lint filter and selector knob. Closed the breaker and turned on the machine, no noise!!!
Incidently I am 78 years old. Thanks PartSelect.

Help other customers find the most helpful instructions.

Were these instructions helpful?

20 of 30 people found this instruction helpful

Parts Used

Level of DifficultyReally Easy

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerWilliam from Leesburg, IN

Only orderd two sliders needed four

easy no problem

Help other customers find the most helpful instructions.

Were these instructions helpful?

17 of 23 people found this instruction helpful

Parts Used

  • Lint Filter and Frame

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

Tools

CustomerMark from Clarksville, VA

Replacement of holed lint screen

straightforward swap, just form the top rail and click it in

Help other customers find the most helpful instructions.

Were these instructions helpful?

21 of 41 people found this instruction helpful

Parts Used

Level of DifficultyA Bit Difficult

Time to do repair:15 - 30 mins

ToolsScrew drivers

CustomerMonaLisa from Bronx, NY

Horrible screeching noise when the dryer drum was in motion, cracked pieces were tangling and ripping the drying clothes.

I removed the top of the dryer (unscrewed from the inside to release the top). Removed interior screws to pull open the front of the dryer. Once inside, it was really visible that the old parts (front air duct top and bottom) were in bad shape. They were cracked and broken. I removed the old pieces (they pretty much cracked and crumbled right off). I snapped in the new pieces careful to avoid damaging the electrical connections and wires. Once snapped into place (top and bottom), I careful put the front back into place making sure that the dryer drum rested on the new pieces. All screws back in place and all done! Dryer is now working as new!!!

Help other customers find the most helpful instructions.

Were these instructions helpful?

13 of 21 people found this instruction helpful

Parts Used

  • Lint Filter and Frame

Level of DifficultyReally Easy

Time to do repair:Less than 15 mins

Tools

Customerwilliam from simi valley, CA

New lint filter

my problem was easy, i orderd a new lint filter, for a
dryer that is at least 10y/o. it came to me by FEDEX,
in 3 days. i threw out the old one and put in the new
one. easy peasy. i will say that this website had what i
wanted and got it to me very quickly. good job by
PARTSELECT......

Help other customers find the most helpful instructions.

Were these instructions helpful?

1-5 of 14