Quick Question!

Have you ever purchased from PartSelect.com before?

11757611-1-S-Whirlpool-WPY913200-Drain Valve Lever Lifter
11757611-1-S-Whirlpool-WPY913200-Drain Valve Lever Lifter 11757611-2-S-Whirlpool-WPY913200-Drain Valve Lever Lifter 11757611-3-S-Whirlpool-WPY913200-Drain Valve Lever Lifter http://www.partselect.com/Schematics/Maytag/39359.gif

Drain Valve Lever Lifter

PartSelect Number PS11757611

This black lifter is just over an inch long.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Not draining.
  • Will not fill with water.

Compare At

$9.95

You Save

$1.66

Your Price

$8.29
Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.4 / 5.0, 4 reviews What's this?
1-4 of 4
 

21 of 27 people found this instruction helpful

Parts Used:
  • Drain Valve Lever Lifter
Level of Difficulty: Easy
Time to do repair: 1- 2 hours
Tools: Pliers, Screw drivers
Customer: Christopher from Cape May Court House, NJ

Dishwasher would not drain / pump out the water

First I called a repairman. He saw it was a certain model Maytag and would not fix it. It washed, but would not drain, so rather than buy another I took about an hour to carefully remove the washer and the motor / bowl unit from the body. Then it was easy to see what was wrong. The problem was a broken lifter arm in the bottom of the bowl. This caused the drain solenoid piston to "travel" too far and actually dislodge from the solenoid during use. You have to remove the lower spray arm, drain grate and then the lifter is a little black plastic "arm" on a metal rod that is actuated by the solenoid under the washer. The lifter fits over the rod and is held with a snap ring. Re-assembly was easy.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

12 of 16 people found this instruction helpful

Parts Used:
  • Drain Valve Lever Lifter
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: gary from webster, TX

The lifter broke so the washer would not hold water.

had to remove the spray nozle and cover from the bottom of the washer to expose the stem where the lifter mounts. I had to turn the stem slightly to install it, this had to be done from the bottom of the washer and it took an extra set of hands. Once the stem was in the right position the lifter slid right on, I attached the retainer ring and put the othe parts back on. It works as good as new now.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

8 of 12 people found this instruction helpful

Parts Used:
  • Drain Valve Lever Lifter
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Pliers, Screw drivers
Customer: Steve from Collierville, TN

Dishwasher wouldn't drain

Take the bottom skirts off of front. Put drain solinoid back in its bore and secure with wire or a rubber band.It will be a chrome cylinder hanging Take the center spray section out and look for the broken lever. Get both pieces out if it split and fell in two. Mine usually crack and stay on the shaft. Pull the circlip off and slide new lever in place and replace circlip. Re-assemble center section. If you are going to keep the dishwasher buy extra levers. I buy them 2 at a time and try to keep a spare.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

6 of 9 people found this instruction helpful

Parts Used:
  • Drain Valve Lever Lifter
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Pliers, Screw drivers
Customer: Kenny from Perry, UT

Accidently broke the drain valve lever lifter while fishing around looking for a filter to replace

Once I pulled the old broken drain valve lever lifter off the shaft, the shaft rotated counter clockwise. I then had to turn shaft back clockwise so there was enough room to slip the new part on. Needle nose pliers worked great to hold it in place while regular pliers in the other hand was used to turn the shaft.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-4 of 4