Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS11757600
This dispenser door retaining pin is less than one inch long.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
Door locked light did not come on and did not have 120 VAC across the Wax Motor. Also the Wax Motor did not extend out to make contact with the Door Lock, Spin Enable Switch. General guidance is to replace drive belt and to replace Wax Motor along with the Door Lock, Spin Enable Switches (total of two limit switches). This did not correct the problem. Checked for power and traced loss of power back to the Control Board where resistor R11 was found to be burnt out. Replaced Resistor with new Carbon Film unit, rating of 3.9 K-ohms, 1/4 W and 5%. As a prcaution, replace the Triac (manufactue part number NTE5657), component identified as Q6, rating of 0.8 Amp, 600 VAC. Semiconductor parts must be obtained from somewhere other than Parts Select (unable to find in the small town I live in, I located on the internet at Mouser.com). Unit works great now.
Help other customers find the most helpful instructions.
Were these instructions helpful?
The repair is fairly simple except that the diagram on the web site has an error - it reverses the positions of the long hinge pin and the short pin. I kept trying to do it as the diagram showed and of course it didn't work. Then I followed my instincts! The only other difficult part was figuring out which way to insert the spring but there are only a few options so trial and error was the simplest way.
I took off the rear panel and removed the hose clamps and electrical terminals, slid pump out of slot in bottom pan of washing machine. It only took minutes, this was part of a major overhaul. I replaced this as a precautionary measure. Great prices and quick service,
It was difficult to use the guide provided online to determine what position to place the spring in. Finally I realized that the spring had to be placed with the tip that sticks out against the wall of the dishwasher to make the spring action work. The long and short pins were not a problem. How to place the spring was the main problem, but I finally figured it out. I did not need any special tools to accomplish this. I just used a kitchen knife to push the short pin into place.
There was 4 screws that held the bevel in that still needed to be removed from the old broken one. Once we removed those we were able to place the new bevel and lid in the correct sport, replace the screws and viola, perfect.
The soap dispenser is held to the washer body by means of the bezel and four screws. In my case, the bezel had broken at two corners, allowing the soap dispenser to bang around during spin cycle. In addition, the dispenser lid had broken off, and the hinge pins were missing. NO PROBLEM! Step 1: Remove (and save) four Phillips head screws, and discard broken bezel and lid. Step 2, Using old screws (or new ones from the hardware store -- just make sure they are stainless steel), fasten bezel to soap dispenser at all four corners. Don't over-tighten. Just make it snug. Step 3: Insert short pin in short socket in lid, and slide long pin into the long socket -- the one open at both ends, with a groove to allow it to slide back and forth. Step 4: Seat the short pin in the rear socket in the bezel, slide the long pin inward allowing the lid to seat into the bezel, and then (using screwdriver) gently push the long pin through and slide it into the front socket in the bezel, forming a hinge. DONE! No more banging. This 15-year-old washer should be good for many more loads. Thank you, !
First off, unplug the machine. Next remove the existing screws in the plastic dispenser. Then remove the door, there are two screws holding the door on connecting two brackets which need to be lifted to get them to release. That gives you the access to the remove the front panel, which is done by pulling on the panel itself. Once that is done you need to remove the two screws that are in the corners upper left, and right that are holding the brackets that hold down the top of the machine. Remove the brackets by gently turning them. Once done the lid should easily lift up. The dispenser can then be disconnected by removing the 2 rubber hoses on top and the the larger rubber hose on the bottom along with the electrical connections under the unit. Keep track of which wire goes to which lead. After removing the dispenser just do everything in reverse. The machine is like new, and the repair took about 45min and saved me at least $200 dollars.
It was a hassle. We didn't have sufficient information in the user's guide to figure out how to attach the soap dish door which had come off back onto the door of the dishwasher, so when we bought the parts, a long pin, a short pin, and a spring (hinge pin), we could only guess how to put it together. The first two times we tried, the pins and spring came off in the dishwasher during a washing cycle and disappeared down the drain. We had to call someone out who just ordered the parts again and said it would cost us $146 to fix, which I thought was ridiculous, so when the parts came, I tried again. This time I figured it out by using a screw driver and hammer to knock the short pin into place while holding the door in place. The door appears to work fine now but, I have yet to use the dishwasher to know for sure.
Removed 2 of 4 the screws that were holding the Dispenser Bezel in place. Removed the broken Dispenser Bezel and the other 2 screws. Cleaned the 4 screws (remove the detergent) cleaned the inside of the Dispenser area. Assembled the Dispenser lid /bezel assy. Secured the lid / bezel assy to washer with the 4 screws. Installed the syphon cup and syphon cap.
Went on line to find the part numbers, ordered complete replacement. Simply put the stuff together and replaced the whole cup lid.
Be sure to check for all parts you will need for repair.I didn't realize I needed to get the pins, springs for lid separately when I ordered the lid. So had to have two orders-but the installation was easy-husband did it.
One of the hinge pins was rusted out, so ordered replacement pin. Parts arrived within 24 hours. Put old long pin in one side, pushed new short pin through inside door hole. Put door in place, pushed pin out to door frame. Done!
There were two parts to the repair - the Dispenser Lid and Bezel was easy - I did it myself.My wife, who normally would try to do the repair of the door lock herself has been very busy with her condo rental business. It took six weeks to get her to order the parts and then they sat in the box for two weeks before I convinced her to call her appliance repair company she uses for the renatl condos. They did a quality job for only $79.00. When my wife saw what he had to be do to repair the locking mechanism, she was convinced we made the right decision. The Maytag washer is working like new after weeks of manually adjusting the door latch, sometimes a dozen times, before it would lock and do a high speed spin.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.