Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS11757553
This two inch wide idler pulley wheel is beige in color and is made of plastic. This pulley wheel comes with its own metallic bearing in its center.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
Took the front off the Dryer removed the drum. Replace drum rollers, Idler pulley wheel with bearing, and drum belt them replaced drum belt and reinstalled the drum. Put the front back on the dryer job complete.
Help other customers find the most helpful instructions.
Were these instructions helpful?
i took the dryer apart to research the squeak. could tell the issue was coming from the idler pulley (the pulley the belt goes around. but since i was taking the whole thing apart i got two new rollers and slides and a spare retaining ring in case i broke the old one during install. in most cases i would purchase a new belt also, but mine still looked new.always unplug the dryer first. then use a flat balde screwdriver and put in between dryer top and dryer body a couple of inches from either side of the dryer, do one side at a time and slightly rotate screwdiver this will disconnect clips holding top of dryer on. once the clips are free lift dryer top like a car hood and let lid rest back against a wall behind dryer. draw a diagram of wire connections as you go this will make reassembly easy. disconnect the two wires attached to the door latch, then on the right side and left side of the dryer about two inches from the top there is a self tapping bolt that needs to be removed. once the bolts are out you will be able to lift and pullback on the front of the dryer to remove. three philips screws hold the lint trap assembly to the door assembly i took these out and vacuumed everywhere i could. there is a plastic assembly on the front of the heater unit, three small bolts will remove this. draw a diagram of the wires attached to the blower unit and disconnect. reach behind the blower unit release the tension on the belt by pulling the tensioner puilley forward, you will then with the other hand be able to remove the belt. with the belt removed, 4 bolts around the frame of the drum will enable you to remove the drum making all the repairs very easy. you will see both black rollers in the back bottom of the machine, remove with a set of snap ring pliers and replace the same way-make sure the side that says "front" is facing you when you install. the tensioner pulley with bearing is also replaced with a single snap ring, all three can be replaced in minutes. the slides are plastic pieces that are mounted on the inside of the front panel of the dryer that the drum rolls on. the old ones just slide out and the new ones slide in as long as the brackets are still good, no tools required. put everything together in reverse order, getting the drum back in and the belt back on my require an extra set of hands, but is not hard. dryer sounds new, saved myself hundredss of dollars, i'm sure and once i diagnosed the problem and had the parts, repairs were made inside of an hour.
Removed door and front panel. Removed drum. Removed idler pulley arm and spring. Removed snap ring and pulley from idler pulley arm. Reversed process to re-assemble.
Lay"d dryer on back took it apart 5/16 socket and a snap ring plier, orderd parts on a friday afternoon, parts came tuesday 9:30 AM. orderd all glides and rollers as long as it was apart, glad i did they were shot, real easy to repair.
when i first heard the noise i thought it was the belt. after changing that i still heard the noise but louder. so i took off the bottom face plate took off the door and the bracket holding the tumbler then took out the tumbler to see what was wrong. being a 6' 4" 250lbs it was hard for me to see what was behind the motor. i finally saw that the idler wheel had come half way off of the lever. I changed the pulley lever, pulley wheel and all the washers. it was fairly simple. and when done the noise was gone. it only costed me about $15 which made me happy cheap fix.
Disconnect the dryer from the electrical source. Using a nut driver, first remove the 2 screws of the lower panel and release the panel. Next remove 4 screws of the door panel and then remove the electrical connections to the door (6 wires). Remember to mark the wires prior to removing so you will remember were it plugs back in on reassembly. Remove the door panel. Then remove the 2 screws holding the top of the dryer and tilt the top open about 90 degrees to access the tumbler. Remove the belt by sliding off the tumbler. Remove the tumbler. You will then access the pulley. Using a pair of pliers, remove the retaining ring by pulling upwards. Then remove the washer and the pulley. Replace the parts with the new pulley, washer and retaining ring. This time would be a good time to replace the belt too. Thread the belt through the pulley and over the tumbler. Place the top back and screw in place. Reassemble the door wiring and reattach the door with the 4 screws. Reassemble the lower panel and plug the dryer back into the outlet and test. There should be no more noise if the noise is coming from the pulley and loose belt.
clothes drier didn't work, tore the drier apart, found problem went looking for the part locally, didn't find it, got mad, went on line, found Parts Select, ordered part, part under $20.00 delivered, part delivered, put everything back together , can dry clothes again, didn't have to find $350.00 to go buy a new drier. Merry Christmas!
To start the repair, I removed the two front panels. Disconnecting the wiring to door and light. Next removing dryer drum and drive belt[ allows access to belt tensioner] replace tensioner roller, then reassemble. Dryer works fine
remove the housing under the dryer door. take out the lint trap. I took the whole bottom off the dryer to easily get to the tensioner pully. I then loosened the tub and slid off the old belt and replaced it.
Well, my husband actually did the repair . He took the cover off the dryer, then he removed the drum, removed the worn wheels, replaced with the new. Then he vaccumed out all the lint, put the dryer back together and now its working good as new. And I thought we needed to purchase a new dryer!
Took apart front of dryer, took out tub, replaced pully wheel, put tub back in with new belt, and put front back on. I would recomend replacing wear pads when doing this type of job.
Not my first dryer repair. This is an easy fix, even for a "novice." Just follow the directions that can be found at several websites, and pay attention. Easy to do, and will save you $$$. This is also a good time to clean excess lint out of the dryer! You should also inspect the felt that the drum rotates on. (And sweep underneath the appliance. Who wants to do that on a regular basis!!??)
With your parts and the book from the library, it was a piece of cake.
removed front of dryer, replaced old pully and put on new belt.
Removed the screws holding the bottom to the sides (but after taking it all apart, I think I could have done the repair by just taking the front off :-(. Removed the screws holding the front to the sides. Noted the wiring (three wires go to the front door switch). Removed the wires from the switch (they are quick connects, so no tools necessary). Removed the front. Pull the drum out. Disconnected the spring from the idler pulley lever. Removed the bolt and nut holding the idler pulley lever assembly to the bottom. (The old pulley had basically frozen in place which caused the belt to break). Put the new washers, wheel assembly and retaining ring on the new idler pulley lever. Bolted it back in place. Connected the spring. Put the new belt around the drum and slid the drum into place. Put the belt around the motor pulley and past the idler wheel (make sure it is on the correct side so this takes up the tension). Put the bottom screws back in. Connected the wires back up to the front. Put the front in place. (Make sure that the drum is properly seated in back so the front goes on and the drum will turn). Put the front screws back on.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.