Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS11757475
This electric oven bake element with screw in wire terminals is 19 inches wide. It has a terminal depth of three inches and a total element length of nineteen inches. This element is intended for use with some electric ovens.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
First, I cut the power to the stove to be sure no electrical current could be conducted. Next, I removed the two screws that hold the heating element to the back of the stove. Then, I removed the oven racks and slowly slid the heating element out until I could see the wires that attached to it. Because the element has the female end of the wire, I pulled the male ends out of both the left and right side of the element.. This releases the old element and I discarded it. Next, I took the new element, slide the male ends into the new female ends that protruded from both the right and left side of the element. I crimped these slightly with my pliers to make sure that they would stay secure when I pushed the element into place. With the new element securely attached, I slowly slid the element into place, this forces the exposed wires to be retracted out of sight and in the insulated part of the oven. I then took the two screws that I had to removed in the beginning, and used them to fasten this new heating element to the back of the oven. Finally, I turned the power back on and the element worked fine.
Help other customers find the most helpful instructions.
Were these instructions helpful?
The frame and window were supplied as a completed assembly. About 4 other panels had to be removed prior to installing the new window assembly. This was easy to do with a screwdriver removing about 16 screws and then replacing all panels back in place after replacing the new window assembly. No instructions were supplied with the part, but anyone with a little mechanical abillity could do it. You may need a helper to hold panels in place while they were being screwed back in place. Total job took about one hour
First, I made sure the circuit breaker was off to the oven. Next, I removed the two screws that hold the element in place , pulled the element out a few inches and eased the wires apart at the metal connectors. I eased in the new wires, put the two screws back in, and voila. In under five minutes, the oven was fixed.
Being a single Mom for almost 16 years I have learned to do everything. When the Jenn-Air oven baking element started on fire I freaked out. It turns out that PartSelect.com has the part as usual. I have ordered before for the same appliance and even though it is 15 years old you always have what I need. I removed the old one (two screws in back of oven), measured, logged on, ordered, and the next day installed the new baking element. Even I was able to do this and it fit and worked the first time!!!!
My spouse calls me Mr. Breakit--and she's right. I was delighted to read others' accounts that this was easy, but I wasn't sure. When the part arrived, we had 1 hour before company arrived. I took two screws out of the plate (tight--I had to apply a lot of torque), slid the old piece out, attached the new piece, put the screws back in. Voila! (Oh, yeh, do remember to turn the juice off.) We were "cooking" in about ten minutes. So easy a caveman could do it. And I did.
"First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and removed the two wires." from the burned out element. I plugged in the new element, reinstalled the new element and, 10 minutes start to finish, the oven heats again.So easy even I can do it. !!!
The oven that was in out newly purchased house was a JennAir and over 20yrs old. Worked ok, but as with any heating element, the performance wanes over time. I decided to replace the baking and broiling element...and the oven door seal while I was at it. Everything went well, it was a simply remove/replace. Then I bumped the oven door where it was leaning up against the fridge waiting to be reinstalled. Down it fell on the tile floor. SMASH! Tempered glass EVERYWHERE. Got online with PartSelect and ordered a replacement (very reasonable price). It arrived in 2 days...just like the elements. Replacement was easy. Thanks to PartSelect for having the parts in stock and delivering them in record time!
First checked to see if there was power to the heating element. There was , so I knew the element was bad. I ordered a new heating element and it came in 3 days! I removed the two screws that held the element in place. I then pulled the element out about 3 inches and disconnected the two wires. Reversed the procedure with new element. Turned on oven and my wife cooked a delicious meatloaf.
First I removed the two screws that held the old element in place. Then I pulled the element out about 5 inches so I could reach and pull off the wire clips from the old element. I then attached the wire clips onto the new element and pushed back the wires into the insulated area and when the back plate matched up to the screw holes, I re-inserted the screws and tighten them down. The oven works great.
The hardest part of the repair was getting the old cruddy screws out of the old element. They were sort of "baked-in". Once we got the screws out the rest was really easy. Just inserted the element prongs & screwed the new ones in. Ordering & receiving the part was a snap...I would recommend your company to anyone. Thank you.
remove two screws, pull out element, diconnect two wires, toss old element,plug in wires to new element, replace two screws and viola- doneNow if you just sold faucet parts I'd be all set.
needed hammer to help loose screws .pulled out and replaced leement
First we removed the two screws that hold the element in place. After pulling it from the back of the oven we did not realize that the clips that held the wires could be slipped off the 'tongues' of the element. Therefor we thought we had to cut the wires - which we did. After realizing that the clips came off, we went to the store and bought a box of new clips, stripped a small portion of the plastic on the wire to expose the wire and put it in the new clips and crimped them. Then slipped the new clips onto the new element, replaced it and put the old screws back. You wouldn't need to buy new clips (not expensive) if you know ahead that they can be removed from the old element and slipped onto the new one. We were amazed at how quickly the element arrived in the mail. Have bookmarked this sight for future repairs.
We cut off the electricity to the stove before touching anything. We removed the 2 screws on the plate that is mounted to the inner wall of the oven. Then we pulled the element out 2-3 inches and disconnected the wires. We connected the wires on the new bake element and pushed it into place, inserted the screws and DONE!The bigger part of the "repair" was the clean up of the fire extinguisher residue inside the oven due to the fire.
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires.This same repair 2 years ago thru a Factory repair "professional" had cost $200. My cost $42.00!! Cost to replace the entire range...$1700.00.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2016 , Eldis Group Partnership. All rights reserved.