Quick Question!

Have you ever purchased from PartSelect.com before?

11757388-1-S-Whirlpool-WPW10757217-Circulation Pump and Motor
11757388-1-S-Whirlpool-WPW10757217-Circulation Pump and Motor 11757388-2-S-Whirlpool-WPW10757217-Circulation Pump and Motor 11757388-3-S-Whirlpool-WPW10757217-Circulation Pump and Motor http://www.partselect.com/Schematics/Whirlpool/46WLNAIP.gif

Circulation Pump and Motor

Compare At

$163.73

You Save

$27.29

Your Price

$136.44
Order within the next 12 hrs and your part ships today!
Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS11757388
Manufacturer Part Number WPW10757217
Manufactured by Whirlpool

The circulation pump and motor is located near the bottom of the dishwasher. The part functions by spinning the impeller of the circulation pump, which is used to move the water through the spray arms during the wash cycle. Before you begin this repair, it is recommended that you pull your dishwasher out of the cabinet, so you can tip the dishwasher to one side and gain better access to the circulation pump and motor. Be sure to disconnect the power source and the water source to the dishwasher before you begin this repair. To complete this repair you will need a 1/4 inch nut driver and a 3/8 inch nut driver.

This part works with the following brands: KitchenAid, Kenmore, Whirlpool, Estate, Roper, Inglis.

This part works with the following products: Dishwasher.

This part fixes the following symptoms:

  • Noisy.
  • Not cleaning dishes properly.
  • Will Not Start.
  • Leaking.
  • Will not fill with water.
  • Not draining.

Videos For installing this part.

Questions & Answers

Ask our experts a question on this part and we'll respond as soon as we can.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 2.8 / 5.0, 36 reviews What's this?
 

6 of 7 people found this instruction helpful

Parts Used:
  • Circulation Pump and Motor
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Screw drivers, Socket set, Wrench set
Customer: lisa from columbus, NE

Front seal on the old pump failed causing the front bearing to get wet repeatedly and fail

Removed required hardware and dishwasher from undercounter mount. Turned dishwasher on its front and removed the old motor. Installed the new motor and tested for function. Installed once test was successful.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

7 of 12 people found this instruction helpful

Parts Used:
  • Circulation Pump and Motor
Level of Difficulty: A Bit Difficult
Time to do repair: 1- 2 hours
Tools: Pliers, Screw drivers, Wrench (Adjustable), Wrench set
Customer: Pat from San Juan Capistrano, CA

Water pump was not functioning.

We took off the old one by disconnecting everything and put in the new one an re-connected everything. Aligning the pump was a little difficult.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

4 of 4 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Pliers, Screw drivers, Socket set, Wrench set
Customer: William from AUSTIN, TX

After a loud noise the dishwasher quit and would only buzz when the main motor was supposed to be running.

Primarily, I read the instructions on line and watched the great videos explaining the repair. While the DW was out, I decided to change out the Drain Pump and the Chopper Assembly, even though only the Circulation Pump and Motor was my problem. These three items are the primary mechanical wear components and it made sense to me to replace these items. Perhaps I'll get another 10 years out of the DW. Two notes about the repairs. If you replace the chopper it isn't clear in the video where exactly it fits into the housing as the video mechanic did a great job of blocking the view of this part of the procedure. It took me awhile to figure out the chopper screen didn't go in the narrow trough, but just outside of that trough. Also, to lubricate the gaskets when putting the motor and the drain pump back in, I use a light coating of petroleum jelly. It is a good lubricant to facilitate the insertion of the both pumps. The pumps slid in easily and there were no leaks when I test ran the DW outside of the cabinetry. If you have a modicum of mechanical ability this job is a very simple, straight forward process. Good Luck!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

4 of 7 people found this instruction helpful

Parts Used:
  • Circulation Pump and Motor
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Wrench (Adjustable), Wrench set
Customer: Ronald from Duluth, GA

Dishwasher making up high pitch noise when running

After looking at what everyone else had done, I decide that I would take the dishwasher out of the wall space and set it on its side. This require me to turn off the power first. Then I pull the diswasher out from its space in the wall. I turned off the the water and then took off the water hose, then took of the return hose. There was water left in both, so there was a little water on the floor as a result of this. Then I finally pulled out the unit and laid it down on its side. The motor was very visible and was easy to access. The hardest part was finding the bolt to take it off. I pulled off the power connector to the motor and then took off the one bolt that was holding the motor on the washer. Then I twisted the motor, but it would not come off. I finally got a screw driver and put it in the small opening between the motor and the connection and it finally came off. This took all of about 30 minutes. Once I got the motor off, I notice that the aluminum grating inside was dirty and needed cleaning. So I cleaned this and put it back inside. The new motor came with every thing, so I put it in and twisted it. Then put back in the bolt, reconnected the power cable, put back on the water and reconnected the output cable. In order to make sure there were no leaks before I put it back in for good, I ran a short wash to check to see if everything was tight. There were no leaks, so I put everything back in the wall. It really did sound very nice now. This dishwasher unit came with noise padding, so I put that back as well. The dishwasher, now is very quite and I don't mind it running any time during the day. The hardest part about this is getting the motor off and find the bolt. It is down between motor and the unit and there was some aluminum between this and the dishwasher, so you need a long nutdriver to get it off.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

4 of 7 people found this instruction helpful

Parts Used:
  • Circulation Pump and Motor
Level of Difficulty: Easy
Time to do repair: 1- 2 hours
Tools: Nutdriver, Pliers, Socket set, Wrench set
Customer: Brett from North Jackson, OH

Pump motor made excessive noise with leaking water

Removed dishwasher from cabinets replaced motor which was easy to do reinstalled in cabinets and ran cycle. All was good. No noise and no leaking.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 6 people found this instruction helpful

Parts Used:
  • Circulation Pump and Motor
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Screw drivers
Customer: JOHN from MORA, MN

The problem started with the pump getting noisy then it stopped pumping all together there are two pumps in this machine still drained its self.

First run the cancel and drain cycle to empty the water from the machine. Next shut off the water and power to machine. Then disconect the water and drain hoses, and uninstal the machine from the cabnet. There are usualy just two screws at the top when you open the door. Before you take them out take out the bottom wash arm, and the screan and the cover over the food chopper. These are all held in with star screws. After the cover is taken out the chopper will lift right out. Next lay the machine on its side there is just one capscrew holding the motor in located behind it when lying down but first unpug the wire harnes to it. The motor will come out with just a small twist after the cap screw is out. To instal just twist in put in the cap screw and follow the directions backward till it is installed again.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Circulation Pump and Motor
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Screw drivers, Wrench (Adjustable)
Customer: Ivone from WARE, MA

Leaking

Changing the pump was very easy. The difficult part was disconnecting the water and electricity and connecting it back up.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Circulation Pump and Motor
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Pliers, Socket set, Wrench set
Customer: Howard from MEDFORD, NJ

Dishwasher was very noisy

Turned off the power at the breaker, turned off the water supply, disconnected the water line, removed all three racks, pulled dishwasher out from under the counter, laid the unit on its back, removed the flat plastic water lines from inside the dishwasher, disconnected the hose and all wires (plugs) that were attached to the motor & pump assembly, removed three plastic wedges that held the pump assembly to the bottom of the dishwasher, tried to remove the motor & pump assembly from the inside of the dishwasher but it wouldn't fit through the hole, removed two parts from the motor a silver cylinder with two wires attached to it and a white plastic piece with copper wound wires and magnets in it so that it would fit, once the entire assembly was out removed one screw that holds the motor to the plastic pump assembly, twisted the motor counter clockwise the pulled it straight off, after installing the new motor I removed the silver cylinder (maybe a capacitor) that was attached to the motor leaving the two wires attached to it so that the assembly would fit through the hole in the bottom of the dishwasher, cleaned the rim of the hole and the rubber gasket on the assembly, put the assembly through the hole in the bottom of the dishwasher, installed the three wedges to hold it in place, then put it all back together. When I ran the dishwasher it was as quiet as when it was new.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Circulation Pump and Motor
Level of Difficulty: Really Easy
Time to do repair: 1- 2 hours
Tools: Pliers, Socket set
Customer: Gordon from BOERNE, TX

Very noisy.

Removed dishwasher from cabinet and turned on side after disconnecting water line and drain line. Motor/pump was very easy to apply. Reconnected supply lines and installed back under counter top. Took more time to get everything out of the way than actual repair. Video instructions on U-Tube is most helpful.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Circulation Pump and Motor
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Pliers, Screw drivers
Customer: Lawrence from GENESEO, IL

Pump leaking water

Disonnected, drained and pulled dishwasher. Tipped on side, disconnected electrical plug, took out screw, twisted pump 1/8th turn, pulled pump. Cleaned screen and reversed order to assemble. Very easy replacement.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Circulation Pump and Motor
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver, Screw drivers, Wrench (Adjustable)
Customer: Lorne from AVON LAKE, OH

Replace circulation pump

Just like all the instruction and videos indicated. No deviations

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Circulation Pump and Motor
Level of Difficulty: Easy
Time to do repair: 1- 2 hours
Tools: Nutdriver, Screw drivers
Customer: dan from ASHEVILLE, NC

Failed circulation pump/motor. Previous motor made increasing loud hum/noise

excellent instructions onvideo. Must see. It helped that I previously have pulled out the dishwasher. It is as easy as the video showed except for one big part. The main bolt holding the pump in place is very tricky to get out. I had to cut some of the heat shield away to allow space for a flexible nut driver extension tool to seat the 3/8 inch nut driver bit onto the bolt. When seated the bolt will remove. You have to watch the video because replacing the new motor has a arrow mark to line up which I wouldn't have known. Final note. Always learn to dismantle the inside mechanisms of your dishwasher. Most "problems" of water flow/noise/lousy dishwashing is because food has gunked up this mechanism. I clean mine more routinely than I want to.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Screw drivers, Socket set
Customer: Thomas from SMITHTOWN, NY

Won't start -- "clean" light constantly blinking -- squeal noise prior to shutdown

Easily replaced motor and pump per video. Located high limit thermostat looking up from bottom and held on with two screw bracket. Reset code: push "Hi temp scour" then push "Air dry" then repeat push of "Hi temp scour" / "Air dry". Works like new - thanks.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 4 people found this instruction helpful

Parts Used:
  • Circulation Pump and Motor
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Socket set, Wrench (Adjustable)
Customer: shane from temple, GA

Increasingly loud whirring noise

The machine we bought was one of the quietest. Until recently it would run without making any noise. My wife brought the noise to my attention and I started troubleshooting. I took it apart to find there were pieces of broken glass in the screens and filters. After that I tested it and discovered that the sounds would only come if the motor itself were operating. Replaced motor....bada bing... I look like a hero to the wife.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Circulation Pump and Motor
Level of Difficulty: Difficult
Time to do repair: More than 2 hours
Tools: Nutdriver, Pliers, Screw drivers, Wrench (Adjustable), Wrench set
Customer: DALE from PHOENIX, MD

Noisy wash cycle

First of all...do not attempt to change the wash motor from underneath. Pull the dishwasher out of the cabinet and then start following the the mfg repair instructions. It may be probable to replace the motor from underneath, but almost impossible. Helps to turn it over, too. Need star-type wrenches. That being said it was not difficult except to break away the water duct from the sump, kept feeling like something was going to break off. (have to force the duct to the right and it does not want to go far enough to come loose easily)But nothing broke and it's running again. Incidentally, the motor assy or cap was not at fault. Had a bad chopper.
Jim

Help other customers find the most helpful instructions.

Were these instructions helpful?   

Model Cross Reference

This part works with the following models:

PartSelect Number: PS11757388
Manufacturer Part Number: WPW10757217
Brand Model Number Description
Kenmore665110739120Dishwasher
Kenmore665110739130Dishwasher
Kenmore665110739140Dishwasher
Kenmore665110739190Dishwasher
Kenmore66513102K900Dishwasher
Kenmore66513102K901Dishwasher
Kenmore66513102K902Dishwasher
Kenmore66513103K900Dishwasher
Kenmore66513103K901Dishwasher
Kenmore66513103K902Dishwasher
Kenmore66513104K900Dishwasher
Kenmore66513104K901Dishwasher
Kenmore66513104K902Dishwasher
Kenmore66513109K900Dishwasher
Kenmore66513109K901Dishwasher
Kenmore66513109K902Dishwasher
Kenmore66513112K700Dishwasher
Kenmore66513112K701Dishwasher
Kenmore66513112K702Dishwasher
Kenmore66513113K700Dishwasher
Kenmore66513113K701Dishwasher
Kenmore66513113K702Dishwasher
Kenmore66513114K700Dishwasher
Kenmore66513114K701Dishwasher
Kenmore66513114K702Dishwasher
Kenmore66513119K700Dishwasher
Kenmore66513119K701Dishwasher
Kenmore66513119K702Dishwasher
Kenmore66513212K901Dishwasher
Kenmore66513212K902Dishwasher