Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS11755809
This gasket wraps around the sides and top of the dishwasher door and helps seal the door when it is closed to prevent water from leaking from the dishwasher during the washing cycle. If your dishwasher is leaking water, first inspect the seal for food particles near the bottom and sides, and remove it. A buildup can stop the door from closing properly and keeping a tight seal. Check the door gasket for tears, cuts, or wear. If the gasket is damaged, you will need to replace it. Before starting the repair, make sure to disconnect the power to the dishwasher.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
I USED A PLUMBER
Help other customers find the most helpful instructions.
Were these instructions helpful?
The whole job took less than 5 minutes...no tools were needed The diagnosis was right on the money
Took off bottom plate (2 screws) and ran unit to ensure where leak is from....it appears to be the door seal. Pulled out old seal with fingers and replaced door seal, ensuring its properly "fitted"..ran unit, no leaks, put bottom plate back on
The old tines on the lower tray were easily removed by bending them in the middle and pulling the ends out of the holders. The replacement tines went in just as easily. The old door seal was pulled out by hand and the new seal was pressed in easily with just using fingers.I was most impressed with the communication in regards to product backorder. They gave me an estimate of product availability and an option to change the order. Great customer service!
Pulled out the old with needle nose pliers. Pushed in new door seal with fingers.
The door seal was easy. In less than 15 minutes I peeled the old one off and installed the new one. Also the new seal arrived in 2 days. In replacing the seal I noticed a screw laying in the bottom of the dishwasher. As I removed the lower washing arm which was real easy I noticed that the plastic bearing for the lower arm was no good. Late Thursday evening I went on line and ordered the bearing, and to my surprise it was delivered to my house on Saturday. In 15 minutes I had the bearing installed and we were back in business. I'm just amazed at how easy your web site is to use, and the promptness of the parts delivery. You guys are great.
Took less than 5 minutes. Pried edge of old door seal out with a flathead screwdriver, then slowly pulled out old seal. Thoroughly cleaned area for new seal with rubbing alcohol, inserted new seal and trimmed the end to fit just right. Presto, no leaks whatsoever!
It was a very simple repair. I removed the old door seal out of the track and installed the new seal.
removed old seal, placed new seal in place. Used my fingers to push it in place. It didn't work as it still leaks. I've put vaseline on the seal and door and it helps but still leaks. The dishwasher doesn't overfill, so I still have the problem, just not as bad.
I opened the door and pulled the gasket from around the dishwasher. The gasket does not have any adhesive around it, so it pulled free almost immediately. The new gasket was pressed into place around the door and I was done. It couldn't have been any easier. I suspected it was the gasket when I saw pinched portions that did not return to the original shape and there were no visible cracks in the machine.
Lowered door and put a weight on it to keep it open. with screwdriver pried out the old gasket. It was simple. looked at the end of the replacement gasket and inserted it into the track with the small hole down. Job Complete. about three minutes total time.
1-2-3 EASIEST JOB I EVER HAD to DO AND THE WIFE IS PROUD OF ME FINALLY. THANKS , , ,Bat from WEST SENECA (Buffalo, NY)
I grabbed the lower right end of the gasket with my Leatherman Tool pliers and pulled out the old gasket.I installed the new gasket. No cleaning was necessary.It took less than five minutes. It now works like new.I ordered the part with standard delivery and it was here in just a couple of days. Very easy fix.
pulled out the old gasket, aligned and pressed in the new gasket
pulled the old door seal off and pushed the new seal into place and it works great!THANK YOU!
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.