Quick Question!

Have you ever purchased from PartSelect.com before?

http://www.partselect.com/Schematics/Maytag/59719.gif
See part 20 in the diagram
http://www.partselect.com/Schematics/Maytag/59719.gif

FAN BLADE AND CLIP ASSY

PartSelect Number PS11754833

If you notice an unusual noise coming from your freezer, the evaporator fan blade might be the problem. Frost-free freezer models use evaporator fans to move air through the evaporator for more efficient cooling. If the evaporator fan blade gets damaged or worn it may become noisy. If the blade is loose on the motor shaft or if the fins are damaged, it should be replaced. Be sure to remove power to the appliance before attempting any repair. The evaporator fan assembly is located behind the air grille or evaporator cover and can normally be accessed by simply removing a few mounting screws. The fan blade is normally pressed on to the motor shaft and secured by a spring clip.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, KENMORE®, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Noisy.
  • Too warm.

Compare At

$5.87

You Save

$.98

Your Price

$4.89
Get this part fast. Average delivery time via standard shipping: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.2 / 5.0, 3 reviews What's this?
1-3 of 3
 

47 of 52 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: James L. from Madison, AL

Froze over fan motor burnt out

Removed shelves from inside freezer then removed 4 screws holding cover panel. Pulled panel up and slightly pulled forward to remove. Removed wiring connections then removed two screws that held the motor & fan assembly. Removed the support bracket from the old motor and installed same on the support bracket. Reversed removal procedures for installation. Cover panel is a little bit of a problem when trying to reinstall. Put in panel as high as you can and then slide down. You must then exert a little pressure on the bottom portion to get it to seat correctly. Install four remaing screws and you are done. I had this repaired previously by a professional repairman and noticed from the pictures you folks provided that he had installed the screws on the support bracket incorrectly. That was the reason for the fan blade to rip apart.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

18 of 21 people found this instruction helpful

Parts Used:
  • FAN BLADE AND CLIP ASSY
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: GREG from FLAGSTAFF, AZ

Broken fan blade, missing two blades

Turn off power to freezer. Removed two shelves, removed four phillip screws and cover. Used 5/16 nutdriver to remove two fan motor bracket bolts. Did not disconnect wiring, had enough room to flip motor over and remove broken fan blade and attach new fan blade. After reading remarks from another home tech, I reversed the bolts holding motor to bracket, so nuts would not come in contact with fan blades again. Still not sure why fan would of slipped down to break. Running good now!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 6 people found this instruction helpful

Parts Used:
  • FAN BLADE AND CLIP ASSY
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Henry from Weatherford, TX

Two blades on fan broken off

Ordered fan from Parts Select installed on fan motor and replaced cover.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-3 of 3