Quick Question!

Have you ever purchased from PartSelect.com before?

11752886-1-S-Whirlpool-WPW10325124-Phase Control Board
11752886-1-S-Whirlpool-WPW10325124-Phase Control Board 11752886-2-S-Whirlpool-WPW10325124-Phase Control Board 11752886-3-S-Whirlpool-WPW10325124-Phase Control Board http://www.partselect.com/Schematics/Whirlpool/4RJMBESC.gif

Phase Control Board

PartSelect Number PS11752886

Used with stand mixers.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, KENMORE®, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

Compare At

$42.94

You Save

$7.16

Your Price

$35.78
Get this part fast. Average delivery time via standard shipping: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.5 / 5.0, 5 reviews What's this?
1-5 of 5
 

41 of 57 people found this instruction helpful

Parts Used:
  • Phase Control Board
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Pliers, Screw drivers
Customer: Donald from Tampa, FL

Speed surging, especially on low setting

Remove one screw on rear cover. Note wire colors coming from pcb at top of assy.
Replace electronic speed control pcb. You will probably have to loosen the two screws holding the brass end plate assy to install new pcb.
Note the number of turns you loosen, so you get it back in the same position. Tighten locking nuts on screws.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

5 of 6 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 1- 2 hours
Tools: Pliers, Screw drivers
Customer: Michael from MONTROSE, CO

Mixer only had 2 speeds with the smell of electrical burning.

This mixer was given to me 8-10 yrs ago with only 2 speeds (cant believe i waited this long to fix it). Repair went good, wasn't sure what i should replace so i replaced Control board, control plate, governor, grease in the gears and the transmission gasket. I first took any and ALL measurements for any screws on the control plate, this will help when you set your mixer speeds when its all back together. When installing the new governor i used a 10mm socket and a mallet to seat it all the way till it stops on the set pin. installed the new control board, with thermal grease on the back of the plate(very important). Didn't need to replace the grease in the gears, but i figured since i was in there id replace it. (No smells and all gears work) I used it to ground 5lbs of elk into burger (speed 4) after repairs and it worked great. Still have about 15lbs left to do and itll do it with out braking a sweat. Maybe i should open up a repair shop to fix these suckers...lol its that easy. What really helped with the repairs is the youtube video from Partselect. Second to none with a step by step on how to replace and repair just about anything on your mixer. Good deal, if i need to replace anything else i know where to go! Thanks

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Phase Control Board
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Pliers
Customer: Joan from HALEYVILLE, AL

One speed only and surging

I replaced the phase control board because the mixer had only
one speed and was surging. I noticed from other posts that it
is important to note the setting of the speed plate before you
remove it in order to remove the phase control board. Also be
careful removing the associated 'slip-on' terminals as it would
be easy to damage the speed plate. If I ever do this again I
will go ahead and replace the speed plate, probably the cheapest
item to replace. The operation was a success and the mixer is
back in business. Thanks.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Very Easy
Time to do repair: 30 - 60 mins
Tools: Pliers, Screw drivers, Socket set
Customer: Gonzalo from HAINES CITY, FL

Motor did not turn on.

I removed the excess of grease to clear all parts. Then I installed new mechanical parts. Finally, I installed all electrical parts. I followed a logical sequence of removing and installing steps. Tip: Never remove parts without a logical order of sequence.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Phase Control Board
Level of Difficulty: Very Easy
Time to do repair: 30 - 60 mins
Tools: Screw drivers
Customer: marc from MOBRIDGE, SD

Mixer wouldnt turn on

watched an internet video to see what to do. Unfortunately even after replacing the chip the mixer it still didn't work.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-5 of 5