Quick Question!

Have you ever purchased from PartSelect.com before?

11750655-1-S-Whirlpool-WPW10224430-Detergent and Rinse Dispenser with Cap
11750655-1-S-Whirlpool-WPW10224430-Detergent and Rinse Dispenser with Cap 11750655-2-S-Whirlpool-WPW10224430-Detergent and Rinse Dispenser with Cap 11750655-3-S-Whirlpool-WPW10224430-Detergent and Rinse Dispenser with Cap http://www.partselect.com/Schematics/Whirlpool/UOA85Q0U.gif

Detergent and Rinse Dispenser with Cap

PartSelect Number PS11750655

This part releases the detergent and rinse aid into the dishwasher.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Will not dispense detergent.
  • Door latch failure.
  • Not cleaning dishes properly.
  • Door won’t close.

Compare At

$100.40

You Save

$16.73

Your Price

$83.67
Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.3 / 5.0, 8 reviews What's this?
1-8 of 8
 

45 of 50 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: Jim from Sherwood, OR

The dispenser door was broken, would not close.

First I removed the (8) screws holding the front door panel on. Then I took the door panel off and unpluged the ribbon wiring so the door was free from the dishwasher. I then unpluded the wiring going to the dispensor. Then I removed the (6) screws holding the dispensor into place and then sprung the holders (2) so the dispendor could be removed. I stuck the new dispensor in its place, pushed it in so the (2) metal holders locked into place, then replaced the (6) screws, pluged the wiring into the new dospensor, pluged the ribbion wiring back in and replaced the front door panel and reinstalled the (8) screws that hold the front door into place. And then tested and everything worked fine.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

19 of 21 people found this instruction helpful

Parts Used:
  • Detergent and Rinse Dispenser with Cap
Level of Difficulty: A Bit Difficult
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Roger from Idaho Falls, ID

Soap dispenser door catch broke off

1. Disconnected power chord.
2. Removed panel front (8 screws).
3. Taped rubber protector away from dispenser.
4. Removed dispenser mounting screws (6 each).
5. Disconnected two wire cable connector (note: depress small catch on connector to release.
6. Remove old dispenser assembly and install new.
7. Make sure rubber protector sheet is in place before tightening screws.
8. Reconnect two wire cable.
9. Reinstall panel front. Second person helpful to hold panel in place.
10. Reconnect power chord and your ready to go.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

16 of 16 people found this instruction helpful

Parts Used:
  • Detergent and Rinse Dispenser with Cap
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Patrick from Platte City, MO

Latch on soap dispenser failed

I removed the 10 screws that hold the front door panel on and then I removed the 6 screws that hold the dispenser in place, pried slightly on the 2 clamps that hold the dispenser in place, unplugged the wire to it and pulled it out.
Put the new one in and reversed the steps. Presto done!
Works great.
Thanks Parts Select.
PS
Kitchen Aide come up with a better design!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

6 of 7 people found this instruction helpful

Parts Used:
  • Detergent and Rinse Dispenser with Cap
Level of Difficulty: A Bit Difficult
Time to do repair: 1- 2 hours
Tools: Nutdriver, Screw drivers
Customer: daniel from corte madera, CA

Soap door latch pin broken

Needed to replace whole soap dispenser unit. Had to take front door apart cause the hex screws are on the inside. (10 Screws) then doors falls off onto floor if not careful. Spring loaded inner door wants to go up and outside door wants to fall off pulling on wiring. Unplug wiring to solinoid,(plug has locking release lever that needs to be pulled on) remove 6 hex screws, and dispenser comes out. Install new unit with 6 screws, plug in, and get help holding door parts together while installing the 10 screws. You are now finished. Pros are you get the complete unit, and not a bunch of parts. Cons are no diagrams or instructions/no new 6 hex head screws-reuse old ones. . . . . . Do not use soap powder/causes damage to latch parts/use only liquid soaps. . .

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 4 people found this instruction helpful

Parts Used:
  • Detergent and Rinse Dispenser with Cap
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Pliers, Wrench set
Customer: John from Sanibel, FL

The soap dispenser door latch was broken

I removed the front of the dishwasher. Then removed the old dispenser assembly, and installed the new one. I don't have as many tools as I need here in our winter residence, so the job took a few more minutes than it would if I'd have had the correct tools.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 3 people found this instruction helpful

Parts Used:
  • Detergent and Rinse Dispenser with Cap
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: Mike from Redmond, OR

Soap dispensor door was warped

The repair was easy, no instructions with the part. I had a bad leak the first go round, found out that I did not have it centered with-in the indentation on the door panel, so I got to install it twice.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 2 people found this instruction helpful

Parts Used:
  • Detergent and Rinse Dispenser with Cap
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Carol from Pipersville, PA

The detergent dispenser was broken.

Replaced the detergent dispenser using the directions on the shipping notice.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

5 of 15 people found this instruction helpful

Parts Used:
  • Detergent and Rinse Dispenser with Cap
Level of Difficulty: Really Easy
Time to do repair: 1- 2 hours
Tools: Nutdriver, Screw drivers, Socket set, Wrench (Adjustable)
Customer: Eleanor from Middlefield, OH

Dispenser cover was broken

The repair went okay. The problem was that the dishwasher would not run after the installation of the dispenser. The door was taken apart 2-3 times. I told my husband (the repair man) that we should pull out the dishwasher so I could clean behind it. I asked him 4 or 5 times to pull out the dishwasrer. Never an answer. Mind you he is an electrician by trade now retired. For some reason while I was not looking he did pull the unit out after 2 hours of fussing with this electrical problem. Remember he is an electrican by trade. When he pulled the unit out "THE PLUG WAS OUT OF THE SOCKET". How funny!!!!!!!!!!!!!!!!!!!!!!!!!!
I could not stop laughing. I had to answer the phone at that time and my friend thought I was out of breath from running for the phone. I told her later it was from the PLUG OUT OF SOCKET TRICK. I still am laughing. The first thing an repair mann will ask you is if the unit is pluged in. I have two sons and one son-in-law that are electricans and will have many years of fun telling this story. It is good to laugh. I will be laughing for a long time.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-8 of 8