Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Lawrence K - 28 days ago
Verified Purchase
Easy repair
The part fit perfectly and the video made it a piece of cake. Very pleased.
★★★★★
★★★★★
Christopher B - January 28, 2022
Verified Purchase
Dishwasher soap dispenser
Fast delivery, fit perfect, of course you have to remove the outer skin of the door to access the mounting screws. It is electronic controlled so you have to hook up the wire that goes to it. all straight forward
★★★★★
★★★★★
Ralph P - January 14, 2022
Verified Purchase
Part fit perfect
The part arrived faster than expected, fit perfect and made the dishwasher work as designed!
★★★★★
★★★★★
Gordon C - June 30, 2021
Verified Purchase
Right Part.
Right Part. Easy to install. No problem works as intended.
★★★★★
★★★★★
Harold L - April 2, 2021
Verified Purchase
The repair was straight forward
The part was a different color than the door, but that makes no difference. It works!
★★★★★
★★★★★
Diane N - July 29, 2020
Verified Purchase
So happy the part worked!
The part was new, not hard to replace and it worked right away! Happy Mama.
★★★★★
★★★★★
Calvin P - October 5, 2019
Verified Purchase
Have not installed part yet
Have not installed part yet
★★★★★
★★★★★
Dana M - November 8, 2018
Verified Purchase
Simple, easy repair!
The new soap dispenser installed easily with no complications. It was an exact fit.
★★★★★
★★★★★
Monica B - October 16, 2018
Verified Purchase
Slam Dunk
Easy install. Works great!
★★★★★
★★★★★
David M - June 9, 2018
Verified Purchase
Satisfactions
Part fit and works great
< Prev
1
2
Next >
Customer Repair Stories
Average Repair Rating: 3.2 / 5.0, 12 reviews.
What's this?
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Soap and Finish dispenser didn't work
I followed the video provided by this site. It was perfect and made the job very easy.
Lawrence from GREEN BAY, WI
Difficulty Level:
Really Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
1 personfound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Getting the large rubber gasket of the Sump / Motor Assembly to seat fully.
After struggling with the Sump / Motor Assembly for over an hour, I applied a generous coating of silicone lube to the rubber gasket, seated the Assembly and put in 2 of the retention clips. Then, with the aid of a 20 weight to hold the Assembly in its fully seated position, I was able to insert the 3rd retention clip. This method worke
... Read mored well but the company video does not show doing anything like this. Without the lube and weight installation is probably a two person job. All the rest of the assembly went easy. The Dishwasher now works like a brand new one.
Repair was easy. Step by step instructions on touTube
Thomas from NEPTUNE, NJ
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Pliers, Screw drivers, Socket set
3 of 3 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Detergent and Rinse Dispenser door latch completely worn out.
I am NOT an appliance technician. I am simply a somewhat handy homeowner. Removal of outer door panel requires removal of two screws from inside the top of the door assembly at the latch, as well as all of the obvious mating screws from around the perimeter of the inside of the door assembly. Use a #15 torx driver bit. Pull top of panel o
... Read moreut (away from the machine) by maybe two inches, then lift the outer panel up to clear the bottom end of it from the lower positioning brackets. DO NOT lever the top of the panel outward. Keep it close to the inner door. It may take bit of an upward tug to dislodge. Careful here - the outer panel will simply fall free. Two wire pigtails that are connected to components on the inner door are short, so be careful not to strain them after dislodging the outer panel. One is connected to the dispenser. Disconnect both as to provide good clearance for the component replacement. The main wire harness is of sufficient length as to not cause a problem. The six 3/16 hex head screws holding the dispenser in place are easy to remove. There are two small sheet metal tabs that keep the device in place after the screws are removed, but a rectangular mounting frame or bezel will come off, along with the little black curtain that protects the unit. The tabs are at upper left and lower right at the perimeter of the opening in the inner panel. They must be levered gently as to allow the dispenser to push inward for removal. After removal, spend some time cleaning the inner surface of the inner panel as to ensure that the new device will make a watertight contact when fastened in place. Bend the tabs slightly back to an inward position, and install the new dispenser with the socket and motor to your left as you look at it from outside the machine. It clicks in to place and stays put. The bezel mounts only one way (in terms of being upside down) and the flat surface must be toward the inner door. Re-positioning the little black curtain is tricky but if you follow the marks in the material from the previous mount it should work out OK. Tighten the screws evenly as to ensure a good seal. Move the outer cover closer and reconnect the two plugs. Use an object to wedge the inner door open by a few inches, and lift the front panel such that you can position it and slide it back down on the inner panel as to re-engage the lower holding brackets. This keeps the bottom of the panel in place during the reassembly. Now for the fun part... The upper end of the outer panel has to be positioned just right against the inner panel in order to seat the two long screws that straddle the latch assembly from the inside. You'll need clamps, or two people. There's a flat rubber seal on the top edge of the inner door. See that it is seated properly, and then that it becomes covered by the outer panel. If one person firmly holds the panels precisely in position, then the other person can install the screws to a point of being mildly snug. The other two longer screws go in the top-most holes at the upper/outer corners of the door assembly. Place them next. From there, you can carefully replace all the rest of the screws. Only after all of the screws are in place should you make all of them tight. You're done.
Read less
Ron from CAPE CORAL, FL
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers
6 of 7 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
The Detergent dispenser was broken.
Replaced the detergent dispenser using the directions on the shipping notice.
Carol from Pipersville, PA
Difficulty Level:
Easy
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers
3 of 5 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Soap Door Latch Pin Broken
Needed to replace whole soap dispenser unit. Had to take front door apart cause the hex screws are on the inside. (10 Screws) then doors falls off onto floor if not careful. Spring loaded inner door wants to go up and outside door wants to fall off pulling on wiring. Unplug wiring to solinoid,(plug has locking release lever that needs
... Read more to be pulled on) remove 6 hex screws, and dispenser comes out. Install new unit with 6 screws, plug in, and get help holding door parts together while installing the 10 screws. You are now finished. Pros are you get the complete unit, and not a bunch of parts. Cons are no diagrams or instructions/no new 6 hex head screws-reuse old ones. . . . . . Do not use soap powder/causes damage to latch parts/use only liquid soaps. . .
Read less
daniel from corte madera, CA
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Nutdriver, Screw drivers
13 of 16 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
soap dispensor door was warped
The repair was easy, no instructions with the part. I had a bad leak the first go round, found out that I did not have it centered with-in the indentation on the door panel, so I got to install it twice.
Mike from Redmond, OR
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers
3 of 4 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
the soap dispenser door latch was broken
I removed the front of the dishwasher. Then removed the old dispenser assembly, and installed the new one. I don't have as many tools as I need here in our winter residence, so the job took a few more minutes than it would if I'd have had the correct tools.
John from Sanibel, FL
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Pliers, Wrench set
4 of 5 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Dispenser cover was broken
The repair went okay. The problem was that the dishwasher would not run after the installation of the dispenser. The door was taken apart 2-3 times. I told my husband (the repair man) that we should pull out the dishwasher so I could clean behind it. I asked him 4 or 5 times to pull out the dishwasrer. Never an answer. Mind you he i
... Read mores an electrician by trade now retired. For some reason while I was not looking he did pull the unit out after 2 hours of fussing with this electrical problem. Remember he is an electrican by trade. When he pulled the unit out "THE PLUG WAS OUT OF THE SOCKET". How funny!!!!!!!!!!!!!!!!!!!!!!!!!! I could not stop laughing. I had to answer the phone at that time and my friend thought I was out of breath from running for the phone. I told her later it was from the PLUG OUT OF SOCKET TRICK. I still am laughing. The first thing an repair mann will ask you is if the unit is pluged in. I have two sons and one son-in-law that are electricans and will have many years of fun telling this story. It is good to laugh. I will be laughing for a long time.
1. Disconnected power chord. 2. Removed panel front (8 screws). 3. Taped rubber protector away from dispenser. 4. Removed dispenser mounting screws (6 each). 5. Disconnected two wire cable connector (note: depress small catch on connector to release. 6. Remove old dispenser assembly and install new. 7. Make s
... Read moreure rubber protector sheet is in place before tightening screws. 8. Reconnect two wire cable. 9. Reinstall panel front. Second person helpful to hold panel in place. 10. Reconnect power chord and your ready to go.
Read less
Roger from Idaho Falls, ID
Difficulty Level:
A Bit Difficult
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
27 of 30 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
2
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
22 questions answered by our experts.
Sort by:
< Prev
1
2
3
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
SUE
July 31, 2017
We have a broken detergent dispenser lid. Do i have to buy the whole panel? Can i not just replace the lid instead? Also, the door keeps popping open allllll the time. I have tried adjusting the u shaped metal latch on the diswahser, but it still pops open. Thinking i might need the latch on the door?? thanks. sue
For model number KUDP02FR
Hello Sue, that is a great question. For the rinse dispenser you can only get the cap as a separate part, anything else you would need to purchase the whole dispenser - PS11750655. For the door it sounds like a new latch and strike may be needed. Door latch PS886294 and Door strike PS11746708. Hope this helps!
11 people found this helpful.
Was this helpful?
Thank you for voting!
Carolyn
December 17, 2017
Instructions how to replace dispenser
For model number ADB1400PYWO
Hi Carolyn,
Thank you for your question. There is a video on our website that you can reference on how to install the detergent and rinse aid dispenser. The dishwasher and part in the video may not show exactly like the one you have, but it will give you a general idea on how to install the part. You will find the video under part number PS11750654. I hope this helps. Thank you and have a great day!
6 people found this helpful.
Was this helpful?
Thank you for voting!
Steve Walker
March 5, 2018
Everything works, but the plastic latch on the pop-up lid in the soap dispenser (in the door) is broken. Is it possible to purchase just the lid, or must i purchase the entire detergent dispenser?
For model number KUDIO2FRBL1
Hello Steve, thank you for your question. You would have to order the whole assembly which is Detergent and Rinse Dispenser with Cap part number WPW10224430. Good luck with your repair!!
5 people found this helpful.
Was this helpful?
Thank you for voting!
Vern
January 4, 2018
The soap dispenser door does not open to dispense the soap tablet do i need to buy the whole unit or can i just buy a new door.
For model number KUD102CRBS2
Hi Vern, Thank you for the question.Unfortunately the door is not sold sepratly,so the dispenser will need to be replaced. Hope this helps!
4 people found this helpful.
Was this helpful?
Thank you for voting!
Dawn
December 18, 2018
The cap on the detergent dispenser does not stay closed. It looks like the small piece to latch onto has worn. Can i replace the lid or do i need a whole new detergent dispenser?Thank you!
For model number KUDL021RBS2
Hi Dawn, thank you for your question. Unfortunately you would have to get a whole new dispenser. The lid would not be sold separately. I hope that helps. Good luck with your repair.
3 people found this helpful.
Was this helpful?
Thank you for voting!
Pat
February 4, 2019
I need to replace my rinse dispenser cap. Most likely wasn't replaced properly after filling well. Found it melted at the bottom of the washer.
For model number KUDS02FRBL1
Hello Pat, Thank you for contacting us. I have researched the model you have provided and have found the part you are looking for is Part Number: PS11746567. Thank you for your inquiry, good luck with this repair!
How do you install the soap dispenser part ps11750655 the latch on mine broke and i need to replace the part.Thank you
For model number KUDU02FRBL
Hello Rosemary, Thank you for contacting us. While we do not have an installation video on our website for this part, we do have installation instructions provided by previous customers. This can be found on the part page for the dispenser, directly below the Q&A. Have a great day!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Jack
September 3, 2019
I have a KitchenAid dishwasher (model: Kudi02irwh2; serial numbers: Ft4106787). Looks like we need a new detergent and rinse dispenser. Is the one (wpw10224430) listed on your website fits for this model? Is there a link for a installation video? Thank you.Jack
For model number KUDI02IRWH2
Hello Jack, Thank you for contacting us. I have researched the model you have provided and have found the part you are looking for is PartSelect Number PS11750655. Here is a link to a video that may help. Good luck with the repair!
https://www.youtube.com/watch?v=I9pywetfQOg
2 people found this helpful.
Was this helpful?
Thank you for voting!
Chris
February 20, 2020
Dispenser works fine but I keep on filling rinse aid and it keeps on leaking. Any fix for it specifically?
For model number KUDS03FSSS4
Hello Chris, Thank you for the question. This sounds like the seal on the cap is worn and the cap may need to be replaced. We hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Bruce
December 22, 2017
Detergent dispenser pin that holds detergent in place broke, do i need to replace whole unit, and can i do repair myself?
For model number WDF310PAAW1
Hi Bruce,
Thank you for your question. Yes you would have to replace your dispenser to replace that part. Yes you should be able to do the repair yourself. It all really depends on how handy you are. We have answered how to install this part in a previous question. Here is a video that will show you how: https://youtu.be/I9pywetfQOg . It will not be of exactly your model but almost all dispensers are installed the same way. Good luck with your repair.
1 person found this helpful.
Was this helpful?
Thank you for voting!
< Prev
1
2
3
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
