Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS11748730
This bisque door latch with the switches is a simple on/off mechanism that prohibits the dishwasher from operating when the door is open. Please NOTE: The bisque handle is no longer available separately. Only available with this assembly.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
First - Make sure electricity to the dishwasher is turned off. Very important for there are exposed electrical connectors in the location where you will be making the repair. Second - removed the inner door liner. Removal is by unscrewing the tork screws around the perimeter of the assembly (when you take this inner door liner/cover be careful because the door weight dynamics change and you will need to somehow put a weight on the door to keep it open. Becareful here the metal of the door is very thin and can be damaged if not careful when placing the counter weight - you will see what I mean). Third - disconnect the electrical wires from the door latching assembly micro-switches. Do this by unplugging the connector from the switches - be advised, the connections are tight and takes some effort to unplug (again - make sure you have turned the electricity off to the dishwasher, there are exposed electrical connectors - very important!!!). Forth - remove the door latching assembly. This is done by removing two screws. The new part that I ordered came with the handle, latching unit and two new micro switches - which made the repair easy. Fifth - Re-install the new handle/latching unit assembly. Reconnect the "plugs" for the two micro-switches (make sure you make the right connection of plug to micro-switch). Reinstall the inner door liner/cover (be careful that the bottom part of the inner liner is properly aligned/mated with the lower section of where the door actually meets the dishwasher itself, it has to be properly fitted in order for the door to open and close properly and not leak). Once all is together and the door opens and closes properly, turn on the power and operate the machine. Look for any leaks during operation.
Help other customers find the most helpful instructions.
Were these instructions helpful?
First I removed the Torx screws holding on the door cover (two of these screws also hold the latch assembly). You don't need to completely remove the cover but just keep it slightly separated by hand as you do the work. I attempted to remove the connections to the two switches on the latch assembly but this proved to be very difficult even after applying lubricant so I changed my approach. Since only the latch handle was broken I decided to remove the two switches from the existing latch assembly and attach them to the new latch assembly rather than disconnecting the wiring harness. There are two clips holding each of the switches and by pulling them back you can remove the switch. After this was done I was ready to put in the new latch assembly. I removed the two switches off the new latch assembly and have kept them in case a switch happens to fail in the future. I placed the new latch assembly into the dishwasher door and then pushed the wiring harness (with the old switches attached) into the new latch assembly. Take note that there is a "detent" in the switch that must be pushed in as you slide the switch into place or otherwise it won't seat properly. After putting the two switches back in place I closed the cover and tightened the two screws that hold the latch assembly first and then tightened the remainder of the screws. It took a full 30 minutes but that included changing my approach after the harness wouldn't separate easily from the switches.
The web site was great in finding the part that was required. Once the parts was received ( it took four days to et the part ths was very fast) it took only 30 mins. to complete the repair. I had to remove all the screw on the door, lift up the inside door cover and remove the handle latch assembly. I removed the two mico switches from the old handle and installed them into the new handle. I replaced the new assembly and replaced the inside door cover and replaced the screws. This was a very easy repair.I had called a local repair shop to see what it would cost to repait the dishwasher. They told me that it would cost $60.00 to come to the house to see what was wrong with the unit. Next they would charge $75 per hour (minimum of $75 if it was less than one hour of repair time) for the repair plus the parts. THis repair cost me less than $30 plus 30 minutes of my time. Great savings
-Remove all torx screws on door (2 min).-unplug switch's (10 min) I used a small curved awl for this, there is a small nub that goes into the connector that needs popped off to release. I got the first switch in a few seconds, the second took several minutes.-plugged in new switches and replaced torx screws (2 min.)-another job well done.The pictures on the web site were not accurate. I thought i needed the Latch assembly and the latch assymbly (Bisque)M. The Latch assembly Bisque had everything that the Latch assembly had plus the handle (and it cost like $8 less. So I had to return the Latch Assembly. Hopefully I made that clear I saw similar info when I was making my purchase but it was not clear so I ended up ordering more than what I needed.
1st, shut off the breaker for the dishwasher.2nd, opened the door and removed all of the torx screws holding inner door to outer door.3rd, placed inner door up and held it out of the way (closed inner door through/around latch tab and folded up a piece of paper, threaded it through latch tab hole and placed a small piece of masking tape around the paper to hold door out of the way - this made the entire job easier, because you do not need to hold the door out of the way anymore).4th, removed broken latch/handle assembly (carefully - it is always a good idea to collect/save broken pieces to piece together the "puzzle" in case you need to improvise. Removing the metal clip attachments is tough, but much easier now that the inner door is secured out of the way. They cannot simply be pulled straight out. You should use a gentle back and forth wiggle motion in a T-shape. Meaning, wiggle back and forth 1-way, and then the other way (perpendicular to the first way) - this should get them separated. Be patient with this procedure - it will work fine and you won't get frustrated.5th, look at the situation to determine exactly what went wrong/broke specifically (I was extra screwed, because 1/2 of each of the "U" shaped tabs that hold each side of latch assembly in place were broken - as well as the tabs on the latch assembly. These U-shaped tabs were/are actually part of the plastic outer door. Specifically, they are on the inner side of the plastic control panel display. I could have replaced this part too, but I was trying to do as inexpensive a repair as possible.6th, So - I found 2 nut/bolts in my toolbox (probably 1/8" in diameter - 3/4" in length - I used flat head. Be careful in your selection of bolt length - the least amount sticking out the front of the dishwasher - the better). I drilled 2 holes - in the exact location where these inner door tabs broke off - and entirely through to the outside of the outer door - yes, all the way through. We are talking about drilling through less than 1/4" of plastic - simple. I made sure that I would not be drilling through any lighting display or really important pieces. The holes ended up being situated in plain plastic locations - not interfering with any functions. Be careful in your selection of drill bit size - you want the bolt to fit through the hole obviously, but you don't want the bolt to have too much wiggle room - because it will be functioning as your new tab - that should have as much structural integrity. So, I recommend drilling a hole that is just big enough that you have to use a screwdriver to thread the bolt into the hole.7th - I connected the clips into the new latch assembly - somewhat easier than separating the old one.8th - I placed the new latch/handle assembly into its proper location (resting on the 1/2 mounting tabs that remained on the inner door).9th - I then used a small flat screwdriver to thread the 2 screws in place (yes, screw head on the inside of the door - to function as a tab - the edge of the screw head will hold down on the latch tab ends). I had to tilt the latch assembly forward, to allow just enough clearance to get my small, thin flat head screwdriver in there (on a slight angle, but that's ok). Thread it through until it gently snugs down onto the latch tab.***You can do better than I did if you want to go the extra mile*** Find a small, thin piece of sheet metal or plastic. Drill a hole just big enough for the bolt threads to slide through. This sheet should be cut to the following specs: a rectangular shape just big enough to span across the tab you made with the bolt - onto the inner door tab that it still not broken (the drilled hole to fit the bolt threads through on one end). It is added structural integrity to even better hold the new latch assembly in place. Think of it as a bridge that spans the tops of the U-tabs.10th - After screwing the bolts through until just enough to snug down on the latch assem
1)Turn off breaker to dishwasher.2)Remove screws that fasten plastic liner to outer door with allen wrench.3)Disconnect two wiring connections to latch assembly; this was toughest part of project, had to use pliers to get metal connectors our of sockets.4)Connected new assembly and screwed door back together.
i ordered the parts on sunday night at about 9pm. the parts arrived on tuesday afternoon! i removed the screws on the inside of the door, then removed the latch assembly and unplugged the two connectors. i then plugged in the new latch assembly and replaced the screws. i accidentally ordered two parts i did not need and received an email twenty minutes after i asked how to return the unneeded parts descibing the return process. i have already told three people how awesome your company is. anytime i need appliance parts i won't look anywhere else. you have a customer for life!! thanks for everything.
1. Fully opened door of dishwasher.2. With star driver, removed 11 screws from the insde edge of door.3. Outside front panel of door then is separated from inside panel slightly to again access to, latch assembly.4. Verified that replacement part matched existing part.5. Lifted out damaged latch assembly and disconnected the two electrical leads by gently pulling on the insulated connectors.6. Connected the electrical leads to the coresponding connections on the new part and replaced in the reverse order of above. 7. Total time for repair was 15 minutes.
First and foremost, turn off the power to the dishwasher at the breaker panel. Next, open the door and remove all of the Torx screws along the door edge, except the bottom two. The inner skin will open enough, and there is sufficient slack in the wires, to change out the latch assembly without completely removing the whole inner door skin. Next, remove the wire harness plug from the right switch and then insert it onto the right switch of the new assembly. Do the same with the wires for the left switch. Note, you may need a pair of pliers to remove the wire connector from the switches. Place the switch back in place, lining up the screw holes properly, and replace all of the Torx screws. Turn the breaker back on and you are done.Not only could I get the part from PartSelect.com quicker than I could from Sears, the total cost with shipping was the same as Sears wanted for just he part!
First, we removed all of the screws around the perimeter of the interior door panel and lifted it up. (we didn't take it completely off because that would have required disconnecting wires so we just held it up out of the way.)Second, the plastic on the latch assembly was broken so that part came out fairly easily. The hard part was disconnecting the metal prongs that plug it in to the door control wires. We tried everything--prying, pulling--and finally got all three of us in there. One pulled on the latch end of the prongs, the other pulled on the door wiring end of the prongs, and I squeezed the prongs in-between with needle nose pliers. This broke the prongs on the latch side, which was fine since we were replacing the entire latch (the directions in the service manual we downloaded didn't give any indication that disconnecting the prongs would be difficult--I feel like there must be a trick to it, but breaking the prongs worked fine too!)Third, we plugged in the prongs of the new latch--went in easily!--and popped the new latch into place in the door. It wasn't held securely, probably because of the broken plastic, but we replaced the inner door and screwed it in place, and when we shut the door it worked.
1 - Disconnect the electrical power2 - Open the dishwasher door3 - Use Allan wrench to remove the screws from the inside door panel4 - Separate the inside pane from the door5 - Remove the latch assembly6 - Use a screw driver or pliers to remove the electrical connectors from the broken latch assembly7 - Connect the electrical connectors to the replacement latch assembly8 - Place the replacement latch assemble in the door9 - Replace the inside door panel10 - Replace the screws to secure the inside door panel11 – Reconnect the electrical power
Disconnect the power,open panel and remove screws with the exception of the two bottom ones. This allows the panel cover to be opened far enough to pull latch assembly clear.Remove electrical contacts (2) and put defective unit aside. Connect new latch unit to both wire saddles,line up unit with proper holes and install two screws. Once fixed in place,install all other screws and switch power back on.Do a short test run to check for any leaks
Open door and remove all screws to remove front panel. Seperate front panel from door. Remove cover of control box. Disconect ribbon cable that connects control panel to control box. Disconnect wires attached to the switches on the latch handle. Remove all screws attaching panel control to front panel. Remove control panel and latch handle assemblies. Replaced with new parts making sure gasket and seal are in place for the vent. Assemble in reverse order. Cost of parts about $60. Time to repair less than 30 min.
A common theme you'll see thoughout the repair stories; 1. many broken handles at the hinge2. TURN THE POWER OFF. This assembly comes with the microswitches (which is not a bad idea to replace since they are electromechanical and will eventually fail). My only recommendation is to buy a couple of these handle assemblies because they WILL fail. I'm on my 3rd!
removed the inside cover to the door,7 screws, removed the latch assembly, replaced with new parts, back in service.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2016 , Eldis Group Partnership. All rights reserved.