Quick Question!

Have you ever purchased from PartSelect.com before?

11747931-1-S-Whirlpool-WPM0805101-Ceramic Fuse - twenty amp
11747931-1-S-Whirlpool-WPM0805101-Ceramic Fuse - twenty amp http://www.partselect.com/Schematics/Maytag/1976.gif

Ceramic Fuse - twenty amp

PartSelect Number PS11747931

This ceramic microwave fuse is just over an inch long. It is white in the center, while each end is made of metal. This is a twenty amp fuse.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Won’t turn on.

Compare At

$5.87

You Save

$.98

Your Price

$4.89
Order within the next 7 hrs and your part ships today!
Get this part fast. Average delivery time via standard shipping: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.0 / 5.0, 6 reviews What's this?
1-6 of 6
 

31 of 40 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Pliers, Screw drivers
Customer: Jay from Edwardsville, IL

Blows main fuse when the microwave generator start, (cooking function).

Remove microwave from oven cabinet. remove cover and check main fuse with ohm meter.
Tried fuse, it does not blow untill cooking starts.
Check capacitor with ohm meter, after properly performing capacitor dischagre procedure.
Order new capacitor, simple installation. another new fuse and all is good and cooking again.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

20 of 27 people found this instruction helpful

Parts Used:
  • Ceramic Fuse - twenty amp
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Pliers, Screw drivers
Customer: tad from tamarack, MN

Microwave oven blew fuse

First I removed upper front grill by removing two Philips head screws on top and pulling off. This exposed the Philips head screw which holds control panel in place. After removing screw I pushed up on panel and it came off to expose fuse. With needle nose pliers I removed old fuse and again with pliers held new fuse in position. With the help of a bladed screwdriver, I pushed new fuse into holder, then replaced panel, screw and grill. This took less than 15 minutes even as one of the wires on control panel pulled out of connection and took some time to locate where to reconnect, otherwise was an easy fix
.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

10 of 16 people found this instruction helpful

Parts Used:
  • Ceramic Fuse - twenty amp
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools:
Customer: Denice from Montgomery, AL

Microve stopped working

Jenn-Air Microwave would not turn on. Clock worked , light worked, timer worked and would count down .I changed' Part #0813140 Switch, Micr} cost $8.99 plus shippingNow it works Thank You for good advise

Help other customers find the most helpful instructions.

Were these instructions helpful?   

9 of 15 people found this instruction helpful

Parts Used:
  • Ceramic Fuse - twenty amp
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: connie from madison, NC

Died while heating lasagna

Removed 4 small star head screws from back of microwave, lifted body off, removed blown fuse and replaced with new one (found where cord enters). This model is stainless inside and out and I like it a lot. It is also sold by Daewoo and a few other manufacturers.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 2 people found this instruction helpful

Parts Used:
  • Ceramic Fuse - twenty amp
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Screw drivers
Customer: Deborah from STRUM, WI

Microwave went pop and nothing would work.

I mistakenly thought I had to remove the microwave to get to the back, not so. I would have had access to what I needed to unscrew; but I have to admit the hassle of taking it down and putting it back equals having to work on it attached to the shelf-your call on how you do this. I unscrewed the front top to remove the vent piece that is across the top front of the microwave. This will reveal the control panel screw. (While you have the vent removed you might want to clean the vent and the exposed filter.) carefully lift and pull out control panel. I unplugged a piece as the wires were tied tight. It will not completely detach, so carefully tip it back from exposed insides. The fuse is not clear but white with silver ends so look in upper right for it. I popped it out and replaced it. Replugged the wired part to cover and carefully fit tabs in and slide down to secre. Replace screw, replace vent piece and secure screws on top of microwave. I plugged it in to test before putting it back above my stove.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Ceramic Fuse - twenty amp
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Richard from CALIFORNIA, KY

No power to any microwave functions

Access is via RT. SIDE Panel as you face microwave. There are three screws on the bottom right edge to loosen. After that the side panel slips down and off. the fuse is located in the rear near where the power cord comes in. It is the white ceramic tube 1/4" in dia. and 1-1/2" long. Pull it out like any fuse and replace with new one. Reassemble and you are done!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-6 of 6