Quick Question!

Have you ever purchased from PartSelect.com before?

11747833-1-S-Whirlpool-WPD7605115Q-Freezer Door Gasket
11747833-1-S-Whirlpool-WPD7605115Q-Freezer Door Gasket 11747833-2-S-Whirlpool-WPD7605115Q-Freezer Door Gasket 11747833-3-S-Whirlpool-WPD7605115Q-Freezer Door Gasket http://www.partselect.com/Schematics/Maytag/338.gif

Freezer Door Gasket

PartSelect Number PS11747833

This gasket is a little over thirty inches long and is a little over twenty-four inches wide. It is all white in color and is made of rubber. This gasket is used for a refrigerator's freezer door.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Door Sweating.

Compare At

$113.06

You Save

$18.84

Your Price

$94.22
Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.3 / 5.0, 5 reviews What's this?
1-5 of 5
 

15 of 18 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 1- 2 hours
Tools: Socket set, Wrench set
Customer: PHILIP from SNYDER, NY

Worn out freezer and refrigerator door gaskets

removed inside door panels by removing multiple
screws- 20-30 screws which hold each panel and gasket together to the door. then remove old gasket and put new gasket in place... align new gasket to seat on plastic ridge of inside door panel.. pay special attention to the corners so they are aligned properly without any 'bulges'. then screw each panel back on to the door using the original screws removed. best done with the help of a friend to hold and align the panel while you attach each screw. also after installation with door closed - use a hairdryer to soften up the gasket and allow it to conform to the new space and door application. total time is approx 1 hour per door... i probably saved well over $100 in labor by doing this myself-thankyou part select.com for having my parts... i will visit you again once something breaks or wears out again !

Help other customers find the most helpful instructions.

Were these instructions helpful?   

7 of 8 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver
Customer: Lee from Manhattan Beach, CA

Over time the door gaskets had deteriorated to the point where the air loss in the freezer was causing ice/frost build up in the area of the freezer control.

I began by loosening the door gaskets by backing off the screws about 2 turns with the nut driver. The gaskets pulled off easily. I then heated the new gaskets in the clothes dryer on med heat for about 5 mins. I attempted to reinstall the new gaskets and found this more difficult than it needed to be. My solution was to simply remove both doors, remove all the screws and pull the door liners. Then I was able to easily install the gaskets, reinstall the liners and rehang the doors. As a result of pulling the inner liners was I discovered that 'Ice' had developed in the insulation (fiberglass) in the freezer door. I used a heat gun on low to melt the ice and then ran the insulation through the dryer to fully dry it before reinstallation. These added steps increased the total time for the repair but were well worth it in my opinion.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

4 of 4 people found this instruction helpful

Parts Used:
  • Freezer Door Gasket
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver
Customer: John from Hawthorne, NJ

Original freezer door gasket damaged

removed 30+ screws and interior freezer door panel in order to remove gasket. installed new gasket in reverse order as per instructions and payed attention to proper alignment of said gasket.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 3 people found this instruction helpful

Parts Used:
  • Freezer Door Gasket
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Socket set
Customer: cornelius from chicago, IL

27 y/o refrigerator whos' freezer &frige door gaskets are shot

The repair was done by removing the freezer door. I then remove all maybe 48 screws, lifted the inside panel and removed the the old worn gasket ,replacingit with the new making sure that it was seated properly around the panel. then I replaced all the screws and reinstalled the freezer door. Making sure contact is being made around the entire door, WALA,no more moisture, no more frost inside freezer or frige .AT THIS RATE I MIGHT HAVE THIS OLD FRIGE ANOTHER 27 YEARS.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 4 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: DONNA from AUBURN, PA

Moisture on outside of refrigerator & freezer. The old gasket was torn at places.

Took the doors off,took inner plastic off and old gasket. Put new gasket on and put it back together. Used hair dryer to help shape it. It is working fine now. We saved hundreds of dollars doing it ourselves and not buying a new refrigerator!!!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-5 of 5