Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS11747727
This door latch with the switches is a simple on/off mechanism that prohibits the dishwasher from operating when the door is open.
NOTE: The door latch handle within this assembly cannot be purchased separately.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
This very easy repair made the appliance usable again.First, turn off power to the unit (wall switch, in my case, may be a breaker in your case, just to be safe).Simply removed all of the torx screwdrivers (I think I used torx driver bit #27, maybe #26, found in most security screwdriver bit sets).Had to remove all the screws on both sides and along the top of the interior metal cover of the dishwasher door.Once those were removed, worked the inner half of the door loose from the outer part (it did not have to come all the way off, just held it apart long enough to do the repair).Then found the broken parts that had fallen in and remove them, then gently worked the latch assembly loose from the front panel and found the only way that the replacement part would fit, with the two small hinge points that snapped it into place on the latch assembly.Replaced the latch assembly and moved the metal panel back into place, lining up the screw holes, started the two screws that go into the latch assembly itself and then a couple of screws on the sides to hold the panels together.You can move the metal panel to position it just right before tightening any of the screws down all the way. I started with the two middle screws that held the latch assembly and then added all the rest, tightening them all loosely at first and then adjusting the fit before alternating sides to tighten them all firmly.Latch works fine now.
Help other customers find the most helpful instructions.
Were these instructions helpful?
I removed the screws from the inside of the doorI removed the existing Control panel (carefully) because the circuit board was also attached here.I installed the new latch assembly on the new control panel.I reattached the circuit board and reinstalled all of the screws - now it works great!Everything for under $100 and less than 30 minutes! Thanks for the parts!
removed screws from inside plate of dishwasher door. The assembly was hanging free (not clipped to the door). the old handle was easily removed, and the new one was clipped onto the assembly and put back into place. The screws were then replaced.We had been noticing that the door was becoming increasingly more difficult to open. Extra force was needed. (that's probably why the handle broke in the first place). After the repair, the door opens much more easily.This was probably the easiest repair we had ever had to do. Not only does the door operate much more smoothly, but we saved the cost of a service call.
1. Removed 4 screws holding latch and controls module to the door.2. Went back to your site to check how to get the control module to come loose from the door. I gave it a good upward hit with my hand and it came off. There was wiring that prevented the module from coming completely free. But there was enough room to get to the latch.3. Used a screwdriver to fish out the broken latch parts. 4. Inserted the new latch and gave it a tap to spring the pivot pins into place. 5. Replaced the 4 screws that hold the latch and control module to the door. Job done.
Removed the inside door panel. Had to borrow a friends power screwdriver with a star shaped bit to do this. Removed old latch and inserted new one catching the prongs so they could now lock and unlock by pulling up on the latch. rescrewed the inside door back and all was done.
First, I turned off the power to the dishwasher at the main box. Then I removed the 10 screws holding the interior stainless steal cover to the door. I removed the broken handle and the broken piece from the door. I snapped the new handle in place and replaced the 10 screws before turning on the power.This was the easiest repair job I've done and it saved me at least $100 dollars in labor.Thanks to all who have submited their stories. Great help!
Removed inner stainless steel shell of the door,revealing the broken latch/door handle. The old one fell out, and the new one snapped in. It was as easy as that!
unscrewed the fasteners removed the handle and lock unit replaced the handle, replaced the fasteners
It has been a while since I replaced the handle so I may miss some steps but it was easy to do. To change the Handle. Turn off the power. Open the front door and undo the torx screws from around the door. Lift up the panel. Remove the broken handle and lugs and insert the new handle.(Their may have been a couple of screws on the latching mechanism that had too be removed to replace the handle) After replacing the handle the door would open and shut like a new one but the dishwasher still would not turn on. On further inspection I found a fractured joint on a relay on the control board . Resoldered it and it is working great.The delivery of the part from Parts Select was great,I got the part next day in California.
unscrewed inner lining removed old ,put in new,replaced screws,done
First I turned off the circuit / power to the dishwasher. took out bottom rackfound correct torq bit [thats the kind of allen wrench] used with 1/4 exten. & ratchet wrench. Cracked loose all the screws then took them out.made a note this inner door panel fits inside outer door frame.Then lifted this out /away to access door latch which had electric wires to it.This whole assembly you pulled out from two outer pins that held it in place.Be careful and pull easy and evenly. Then I removed the latch and saw one side was broken. Installing new one you have to be easy and use some force, bend a touch to get both pins into holes. do one side then the other. Then partially tilt the whole assembly to get latch into door opening and push it down into where outer pins go into yokes to hold it in place.Then you must be careful when placing inner door panel back down into outer door.put all the screws in loose,then tighten. I was concerned about water leaking but had no trouble. It seems there is a seal across the bottom of that inner door and when you close door it butts up against another seal across opening on the bottom.Put bottom rack in, closed door, and turned on power. Gave it a rinse & hold and no leaks.
I removed 6 screws and the door face came loose.I removed the old handle ,then the new one snaped in .re installed the screws and i was done.
took 6 screws out around the top of the door.pulled the door apart popped the old handle out ,put the new handle on.snapped the handle assembly back in place.good idea to turn circuit breaker off to dishwasher.their or 2 wires on handle assembly.
Actually, I did two repairs:1) Ordered SUB 12002218 (Front Bowl Tine with Sleeves), part #9. Received it in the mail and made the repair in about five minutes. Then the next day the handle broke, which is repair 2.2)Unscrewed all screws around the stainless doors (10 screws), then gently pulled up on the stainless plate at the point of the door latch. Pulled the old latch out, placed the new one in, then replaced the stainless cover and screws and it works good as new. These two repairs saved hundreds of dollars in repair costs by repair people.
Took out the six Torx head screw out of the door inner liner. Lifted the liner off. The handle mechanism was easily repaired by allowing the old part to fall out and snapping the new one in. It took me longer to find my Torx screwdriver than to fix the handle.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.