Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS11747674
This upper spray arm is a little over fifteen inches long. It is all white in color and is made of plastic.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
The repair was very involved, but from previous experience cleaning the dishwasher, it was worth not having to buy a new one. I removed all of the lower parts down to the motor shaft. That process is tricky, but if you do it methodically, and slowly, it is not too bad. The real problem wash the scum that was left behind by the soap used in the dishwasher. After removing all the parts, I ordered the parts I could not clean, and cleaned the parts I could. I figured out that the door was leaking because of the soap scum buildup on all the parts, causing the water level to raise faster than it could be pumped out. After I received the new parts, I simply put everything back together and it works better than ever now. I used the parts layout on your website to help in aiding me to put everything back correctly. I am very appreciative that I can get parts easily through your website, and not have to hire a "service technician" to come out and do the same thing, for the price of a new washer. Thanks!
Help other customers find the most helpful instructions.
Were these instructions helpful?
Other parts used: Discharge Housing Assembly (#11) Impeller Assembly (Wash Impeller) (#14) O-Ring (#37) Upper Discharge Housing Gasket (#38)Removed upper and lower washing baskets.Pulled off Upper Spray Arm (#33). It pulls off easily by hand. No tools required. Replaced with new Upper Spray Arm (#33) and Snap Spray Retainer (#31).Removed Large Spray Arm Cap(#34,)which has a right hand thread. This allowed me to take the Lower Spray Arm(#2)off.Removed Filter Guard (#36).Next I removed the 6 screws from the Pump Cover & Secondary Filter Assembly (#4) with a Torx screwdriver. Removed Lower Spray Arm Seal(#3), Pump House Filter (#6)(which I cleaned), Assembly, Rinse Arm (#7) Jump Up Nozzle (#1). Unscrewed Discharge Housing Nut(#8) by hand. Removed Support, Wash Arm (#9). This allowed me to remove the three screws holding the Discharge Housing Assembly(#11)with a 5/16th nut driver. Next I removed the Impeller Screw (#12) with a 5/16th nut driver. You must hold the Impeller Assembly (#14) firmly while loosening the nut. Removed Impeller Assembly (#12) and Plate, Suction (#15). Cleaned out area of debris,lint, etc. Put back old Plate, Suction (#15) and replaced Impeller Assembly (#14) with new part. Replaced Upper Housing Gasket and Discharge Housing Assembly with new parts. Put back all parts in the reverse order I removed them replacing the O-Ring (#37) with a new part. This O-Ring goes in the Pump Cover & Secondary Filter Assembly (#4). After completely assembled it ran as good as new!
Replaced the clogged filters and the spray arms and everything worked great. Remove the spray arms using your hand to turn the large plastic nuts. Remove the bottom spray arm, ant the pop up nozzle and then using the Torx bit remove the secondary filter plate. Ten remove the pump housing filter and put back together with all the replacement parts.
found washer arms choked up, they also would not spin removed pump to find filter also choked up and warped, replaced both arms and filter, very easy repair.
Pulled both dish racks out then the spray arms. From there took everything else out down to the top of the motor. Replaced both spray arms and anything that a filter or a screen in it. Got everthing back together and ran the unit full of dishes with no issues at all.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.