Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS11747420
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
removed 4 scews underside of door 2 more at top to remove door handle. than removed front door panel. removed inner sheild by bending 4 tabs.removed outside door glass than insideglass. reversed process to complete.
Help other customers find the most helpful instructions.
Were these instructions helpful?
Overall the project was not bad. There are many pieces to the door. Carefully observe the order in which the door comes apart. This will make putting everything back together a lot quicker. The screws that hold the glass clips in the door were almost impossible to remove by hand. A power drill was helpful. Extra time was needed to wash off the baked on crud. When it was all done, the oven looked brand new.
Video's did not show my door construction so I had some difficulty and surprises. One must disassemble and keep all parts in order of disaasembly with all screws for each part.separated. Be methodical and patient and it will all work out.
There are already good instructions here on doing the repair, so I will just add what I found important. 1) using penetrating oil and an impact wrench on the screws that hold the inner glass to the inside of the oven door - they were rusted tight. 2) the outside glass front sits on the front of the door, on top of the edges of the side pieces, even though it looked to me like the side pieces were meant to go over the edges of the glass - they aren't. The bare side edges of the glass aren't covered with any trim at all. The video on removing the oven door that matched the kind of hinges I had showed taking them off the door as part of disassembly of the door. I didn't find that necessary at all, and you probably won't either. Less parts to have to get back in place. The hard part to me was finding the correct disassembly video to match the oddball hinges, which isn't to say it's a bad design - actually it seems better that the other more common designs. Take out the two screws above where the hinges enter the range, and lift the door up, away from the range, and off. Easy peasy.
Watched video and followed the very accurate and helpful instructions. A #2 Phillips screwdriver was the only tool required. This is an easy job for the average person.
This worked very well, thanks to the advice posted from other users. The only part that was a bit unclear was removing the door. There are small, slotted metal pieces screwed into the sides of the oven to hold the door hinges in the slots. After removing those, I had to hold the door and push it up and down, and a little bit side to side, to get the hinges to start sliding out, but they did. There are no other screws or brackets holding them in place. The hinges are on springs, so they do snap up when they come out of the slots in the sides of the oven. But they only snap to a 90 degree angle, so they won't cut your fingers off. You'd have to hold your fingers right on them to even get pinched. After that, I just kept taking screws out of the door until I got through to the back panel, replaced it, and put it all back together.
Removed door parts & cleaned each, till the glass was reached. Replaced glass and reinstalled parts in order removed.
After reading what other people did for this job I figured I could do this. The inside glass broke after liquid accidently hit the glass from basting.Just followed the digram from the internet to show how the door and glass comes apart. The only thing I had to figure out was how to take the door off. And once I figured that out it went pretty easy.The door comes off just by lifting up on the door and pulling out. Just make sure you put all your parts in order on how they come apart and just replace them them in that order.
I refered to what I had read on repair stories of broken glass...then went to fixing mine and before I new it I was done and glass replaced...it was very easy as long as you watch what you are doing when u take it apart and replace things the same as they were removed......thank you
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.