Quick Question!

Have you ever purchased from PartSelect.com before?

11747249-1-S-Whirlpool-WP9759243-Thermal Overload Safety Thermostat
11747249-1-S-Whirlpool-WP9759243-Thermal Overload Safety Thermostat 11747249-2-S-Whirlpool-WP9759243-Thermal Overload Safety Thermostat http://www.partselect.com/Schematics/Whirlpool/XA4HNFR4.gif

Thermal Overload Safety Thermostat

PartSelect Number PS11747249

This part establishes and maintains the internal temperature of the oven cavity.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Little to no heat when baking.
  • Will Not Start.
  • Element will not heat.

Compare At

$46.45

You Save

$7.74

Your Price

$38.71
Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.9 / 5.0, 9 reviews What's this?
1-9 of 9
 

86 of 95 people found this instruction helpful

Parts Used:
  • Thermal Overload Safety Thermostat
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Pliers
Customer: Frederick from St. Louis, MO

No heat after cleaning oven

This built-in oven was slid out of it's space and set on a box. I removed the back cover with nut driver and located the safety overload device. removed nuts and used pliers to remove wires and replace them. The power must be off to do this repair.Replaced the cover and slid back into place. This could be a lot more difficult if your power cord or gas line is not long enough to make it out of your wall space. Or of your oven is attached well to the frame.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

23 of 24 people found this instruction helpful

Parts Used:
  • Thermal Overload Safety Thermostat
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: Devin from Platte City, MO

Oven wouldn't heat after cleaning cycle

Turned power to oven off. Removed trim screws and trim. Removed screws that anchored oven in cabinet. Removed oven from cabinet. Removed back panel, tested thermal fuse. Determined it was defective, ordered new part and reversed procedures above to reinstall.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

16 of 21 people found this instruction helpful

Parts Used:
  • Thermal Overload Safety Thermostat
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Screw drivers
Customer: Robert from Willow Park, TX

Oven wouldn't heat after a cleaning cycle

Recieved the part promptly. From looking at the diagrams, we knew the overload thermostat was located on the back of the oven. We removed the screws, brackets, etc, slid the oven out, which for us was fairly easy as it's an under counter oven. Located the thermostat, removed it, replaced the new one, connected two clip wires, replaced the oven, turned the power back on and it works like a champ. Total cost was under 50 bucks.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

13 of 16 people found this instruction helpful

Parts Used:
  • Thermal Overload Safety Thermostat
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Kenneth V. from Kent, WA

Upper oven bake and broil elements fail to heat when keypad entries made and indicating correctly

Replacement of the thermal overload safety thermostat very straight forward after sliding unit out, killing power and removing two covers. Tested both old and new and both show continuity (= good). Installed new, restored power and tested for proper operation. Didn't happen. Replaced original and now have new as spare. Now suspect the double line break relay on electronic control board is failed and source of problem. It is common to both elements and immediate before the suspected thermostat in circuit.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

11 of 15 people found this instruction helpful

Parts Used:
  • Thermal Overload Safety Thermostat
Level of Difficulty: Really Easy
Time to do repair: 1- 2 hours
Tools: Pliers, Screw drivers
Customer: Elvin from Richmond, VA

Oven would not heat

This is a drop in range so I had to remove the range and set on a dolly. Turn the dolly around and acess the THRMST-FIX that needed replaceing, it was open. put the range back in its place and could still use the rest of stove until I received the parts 2 days later .
Pulled the range out put the new THRMST-FIX in put the range back together and put the range back in place and it has worked ever since.
GOOD JOB

Help other customers find the most helpful instructions.

Were these instructions helpful?   

5 of 7 people found this instruction helpful

Parts Used:
  • Thermal Overload Safety Thermostat
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: joyce from thomasville, NC

Every time I would try to do the self clean mode on my drop in range the thermostat blows. Last time it was still under warranty. I took the part number from the repair man's invoice to order the new part.

My husband took the back off and replaced it. The repairman suggested pulling the range out into the floor to run the self clean mode. I have owned several such ranges and have never had to do that and won't now. Easy Clean Oven Cleaner will be the next thing I use.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

9 of 19 people found this instruction helpful

Parts Used:
  • Thermal Overload Safety Thermostat
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Joi from Higginsville, MO

Oven wouldn't heat after self-cleaning the oven

The website and diagram of my oven helped me know exactly what was wrong and where to locate the problem. I simply removed the oven door and the trim, pulled the oven out of the wall. After removing the back panel I located the part and put in the new part. Then reversed the procedure.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

4 of 5 people found this instruction helpful

Parts Used:
  • Thermal Overload Safety Thermostat
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: Rod from Dripping Springs, TX

Neither bake nor broil elements came on

Removed four trim pieces; removed four wood screws holding oven in cabinet housing; slid oven out (weighs about 150 lbs and takes two people and a bench to rest oven on. Oven will pull all the way out but not much further because of the electric cord.); Removed back sheet metal cover (bunch of small metal screws); removed wires from bad unit, unscrewed the bad unit and screwed in the replacement unit.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

5 of 8 people found this instruction helpful

Parts Used:
  • Thermal Overload Safety Thermostat
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools:
Customer: karen from bismarck, ND

Quit heating

I have a rental and the tenant called. She said that she had a repair man out to fix the oven but he couldn't~that it needed to be replaced as he could not get parts.I contacted your company via phone and the person was so helpful~he asked the problem, looked up the model and advised me on this!It works like a brand new oven!Thanks you

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-9 of 9