Quick Question!

Have you ever purchased from PartSelect.com before?

11747064-1-S-Whirlpool-WP9742946-Wash Arm Bearing Ring
11747064-1-S-Whirlpool-WP9742946-Wash Arm Bearing Ring 11747064-2-S-Whirlpool-WP9742946-Wash Arm Bearing Ring http://www.partselect.com/Schematics/Whirlpool/D42XRBPB.gif

Wash Arm Bearing Ring

PartSelect Number PS11747064

This part will fit between the newer type lower wash arm and the wash arm retainer nut of your dishwasher.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Not cleaning dishes properly.
  • Leaking.
  • Noisy.
  • Not draining.
  • Will Not Start.

Compare At

$9.61

You Save

$1.60

Your Price

$8.01
Order within the next 3 hrs and your part ships today!
Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.5 / 5.0, 89 reviews What's this?
76-89 of 89
 

0 of 1 people found this instruction helpful

Parts Used:
  • Wash Arm Bearing Ring
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Pliers
Customer: Robert from West St. Paul, MN

Plastic bearing was worn out, in two pieces

Removed center screw, lift up the wash arm, remove the plastic bearing. Line up and insert new bearing put the wash arm back in place on top of bearing. Insert screw and tighten. Done.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Kevin from Budd Lake, NJ

The bottom sprayer was broken,upper sprayer was broken.

Part selection was very easy with the detailed diagram that was provided on the website.The diagram was also very helpful in the instalation. The bottom sprayer neeeded a new bushing and "wing nut"; very easy to install less than 5 mimutes. The top sprayer needed to be unscrewed and replaced with the new assembly. Less than 10 minutes.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: John A from Ocala, FL

Tube to upper spray arm missing

Check your card against your invoice. They added an extra 1.53 dollars that wasn't on my invoice.

Their is really nothing to explain.

1. Upper Spray arm It's just removed 2 screws and replaced the old with the new.

2. Lower spray arm bearing and seal, Removed center wing bolt, removed arm removed and replaced seal and bearing.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Wash Arm Bearing Ring
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: Robert from Smithfield, RI

Water was coming out of the door.

I removed the bolt that holds on the bottom sprayer, removed the worn bushing, replaced the bushing, reinstalled the sprayer and tightened the bolt. It was that quick and easy.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: Gary from Danville, IL

Dishwasher made a squeaking sound when running

The problem was the water powered lower swing arm bearing (bushing) had worn out (had rubbed away part of it's flat surface). First I removed the large screw with the big flat finger grip flanges on the top side of the lower swing arm assembly. this assemble looks like a big hub cap. Lift the assemble up and off the attachment stem. The bearing goes on top and the seal on the bottom. Both just push in place with your fingers. Reinstall the assemble on the attaching pivot point that it was removed from and secure with the large thumb screw first removed. Spin the assembley to check for any binding. Do not over tighten the thumb screw. Water pressure is all that drives this assembly and it should always turn with no obstructions.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: George from Carrollton, TX

Wash arm retainer nutt broke

First I ordered the correct parts. The repair involved removing Wash Spray Arm inserting the Lower Spray Arm Seal, peplacing the Wash Spray Arm, then inserting Wash Spray Arm Bearing Ring, the inserting and hand tightening Wash Spray Arm Retainer Nut.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools:
Customer: Lynda from Syracuse, NY

Dishes weren't getting clean

After looking at the sprayarm, changing detergents and washing every speck off the dishes only to have them come out dirty I decided to replace the sprayarm seal and bearing ring. I didn't really need the sprayarm seal, but figured I had come that far I may as well. It went really well and now I have clean dishes. I spent $26 on parts but a service call is $70 and I still would have had to replace the parts.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
  • Wash Arm Bearing Ring
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: James M from Dayton, OH

Bearing righ had worn out

unscred by hand wash arm are removed old bearing ring, replaced it and re assembled the wash arm.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: Jack from Belvedere, IL

Retainer nut broke

Thanks for the quick survice. The part came in two days. I looked all over town for 4 days for the same part. We will use you site from now on for all of our repairs. All I had to do was screw the new parts inplace ,and we were up and running.
Thanks
Jack & Sue

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 1 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: Joe from Augusta, GA

Wash arm retainer nut was broken

I took the old Wash arm retainer nut out and put the new Wash arm bearing ring and Nut in place and hand tightened. It was fixed in less than a minute. Parts were perfect.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Joseph from Spokane, WA

Washing poorly, irregular noise in wash cycle

I removed the old parts and replaced them with new parts. It failed to solve the problem.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 8 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: todd from woodstock, IL

Broken upper wash arm stabalizer bracket...

very easy to fix..i replaced many other parts while i was at it..figured i d "upgrade". washes much better now....less noisy..

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Wrench (Adjustable)
Customer: Judy from Arlington, TX

Wouldn't wash

Called my son in law and he did it

Help other customers find the most helpful instructions.

Were these instructions helpful?   

0 of 5 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 1- 2 hours
Tools: Screw drivers, Wrench set
Customer: David from Hernando, MS

Leaking dishwasher

Installed all parts. Dish washer still leaks. Wasted my time and money.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

76-89 of 89