Quick Question!

Have you ever purchased from PartSelect.com before?

11747064-1-S-Whirlpool-WP9742946-Wash Arm Bearing Ring
11747064-1-S-Whirlpool-WP9742946-Wash Arm Bearing Ring 11747064-2-S-Whirlpool-WP9742946-Wash Arm Bearing Ring http://www.partselect.com/Schematics/Whirlpool/D42XRBPB.gif

Wash Arm Bearing Ring

PartSelect Number PS11747064

This part will fit between the newer type lower wash arm and the wash arm retainer nut of your dishwasher.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Not cleaning dishes properly.
  • Leaking.
  • Noisy.
  • Not draining.
  • Will Not Start.

Compare At

$9.61

You Save

$1.60

Your Price

$8.01
Order within the next 6 hrs and your part ships today!
Get this part fast. Average delivery time via regular ground: 1.8 days.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.5 / 5.0, 89 reviews What's this?
 

6 of 8 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: David from Deridder, LA

Water leaking out side where water enters

AIR INLET GASKET Had to pull dishwaher out, using instructions sent with part, turn it 1/4 turn counter clockwise, tap with screwdriver and hammer and it came right off. Put the new one on. It was kinda hard to get it to turn the last little bit, I had to use a screw driver and hammer to make it twist that last little bit.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

5 of 7 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Pliers
Customer: Umair from allen, TX

Broken bottom spray arm

I had a broken spray arm on the dishwasher and though i would have to spend $450-$500 on a new dish washer, i ordered parts from part select(even though i was not 100% sure if it will work), the parts were shipped super fast and arrived in 2 days, i was able to replace the broken part and fix the lower spray arm. Part select saved me a lot of money.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

4 of 4 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools:
Customer: Peter from Georgetown, TX

The wash arm retainer nut broke in half and the wash arm bearing ring was completely worn away.

I simply unscrewed the remainder of the wash arm retainer nut, removed the wash arm bearing ring and spray arm bearing ring and replaced them; No tools were required. At the same time I decided to replaced the upper wash arm with a kit from Part Select. This did require the use of a philips head screwdriver. The job was real easy and accomplished within 1 hour.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

4 of 5 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Pliers, Screw drivers
Customer: Brad from Dublin, VA

Lower washer arm came loose- dispenser door would not stay closed

Replaced the lower washer arm retaining nut,bearing ring.and seal in about 3 min.The retaining nut had broken off inside - make sure to remove the broken piece-I used needle nose pliers.
The dispenser took about 35 mins. Removed all the screws around the inside of the door and removed panel.Removed screws holding the dispenser and replaced.I took time to give the dishwasher a good cleaning(inside edge).
Now my wife is happy.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 3 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: Howard from Catlett, VA

Lower spray arm wobble - poor cleaning

Removed the lower spray arm assembly thumb screw and lifted off the spray arm assembly. The lower seal had disintigrated - couldn't even find any pieces in the filter. After reassembly with the new seal and bearing I turned the spray arm by hand to ensure it was not binding. There was still was, what I would consider, some excessive wobble. I fashioned a shim washer out of some plastic from a Folgers coffee can lid and installed it on the thumbscrew threaded shaft and tightened it all down finger tight - it works very well and now, and no wobble.
I relaced the upper spray arm seal while I was doing the job (both the upper and lower seals are the same part #). I figured it would go out on me eventually, so I might as well replace it while I was doing the lower arm work. Kept the old upper arm seal as an emergency replacement.

Cleaned the filter screen of all debris (it is amazing what collects there over time). Cleaned the stainless tub with some spray Greased Lightning, ran the rinse cycle, and then put a few tablespoons of citric acid crystals in the soap dispenser and ran the dishwasher on NORMAL WASH with temperature boost.
Looks new inside; cleans the dishes, glasses and utensils well (no water spotting); and is nice and quite (like when it was new).

Help other customers find the most helpful instructions.

Were these instructions helpful?   

4 of 6 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: Sean from Oceanside, CA

Dishwasher leaks at front door

My dishwasher started leaking at the door. I checked the level, door seal, fill float, etc. Nothing worked. Another reviewer of these parts said to replace the Seal, Lower Sprayarm, the Wash Arm Bearing Ring, and the wash arm. I replaced the seal and the bearing, not the washer arm, as my spray had little to no wear. This fixed the problem! If you dishwasher leaks at the door, it is possible these parts are worn and replacing them wil fix the leak. Thanks to the other reviewer I now have no leaks! Buy a spare nut because they break very easy if overtorqued!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 3 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 30 - 60 mins
Tools: Pliers, Wrench set
Customer: Robert from Bryn Mawr, PA

The plastic retainer nut holding the lower sprayer arm severed

The repair was simple except for removing the thread portion of the old retainer nut from the lower housing. I had to remove the lower housing and separate the male threads of the old plastic nut from the female threads in the lower housing. That took 25 minutes since I did not want to ruin the female threads. Once removed, the new parts went into place easily.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 3 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: Jonathan from Canton, GA

Dishwasher not cleaning well. Latch not opening easily.

Uncscrewed the lower washer arm retaining nut and replaced it along wint the 2 washers. Cleans like new.

Unscrewed the front panal from behind. Removed the inside vent covering. Unscrewed the handle screws and removed the handle. Replaced the handle and screws but not before gouging the back of my hand ( I had a needle and thread) and then reattached the panal and vent cavering. The blow-up diagrams you all have are a great reference. Thanks

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 3 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: Larry from Milford Center, OH

Dishes would not get clean

First I removed the plastic bolt that holds the wash arm in place This exposed the upper ring that was worn out . I then lifted the arm off which exposed the larger ring. I replaced that ring, and then I put the arm back on and replaced the upper ring. I put the plastic bolt back in place and the repair was complete.-- Really Easy plus the dishwasher gets the dishes clean now

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 5 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: Richard from Harvard, IL

Broken wash arn retainer nut

Screwed on a new one. The real story is getting the part. I called about noon one day and the part was dropped off at my house by FedEx the next day. Unbelievable. And the lady I talked to found the part number etc that I needed in a few minutes. Great service at a fair price.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: A Bit Difficult
Time to do repair: 1- 2 hours
Tools: Screw drivers, Wrench (Adjustable)
Customer: JAMES from DURANGO, CO

Leaked after filling when first starting up

replaced door seal,lower door seal and wash arm bearing ring-now it leaked when it was running.put old door seal back in and no leaks. all it needed was the wash arm bearing, also I cleaned out the inside of the water level float,which lowered the water level in the bottom of the dishwasher.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: SUSAN from ROYAL CENTER, IN

Bearing ring missing and retainer nut broken

I put the bearing ring on the washer arm and then screwed on the retainer nut.
Easy to order the needed parts

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Socket set
Customer: robert from cold spring harbor, NY

Water coming out of the washer flooding the floor

I guess some food got caught in the water level sense float and caused it to mal function.
In the diagnosis process, I removed the arm to clean out any debree in the strainer ( found broken glass). I also found that the two rings mentioned above were worn. I replaced them and all is well.
Thank you for fast response with the replacement parts.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 2 people found this instruction helpful

Parts Used:
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools:
Customer: Maria from New York, NY

The nut was broken in half, wash arm worned out

I just had to unscrew the old nut and screw the new one and install the new wash arm bearing ring.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 6 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: JOHN from SPOONER, WI

Lower spray arm nut broken, upper wash assembly was broken

just put the pieces where they belonged and tighten the screws. it longer to figure out how it was supposed to fit than the actual fixing.

Help other customers find the most helpful instructions.

Were these instructions helpful?