Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS11746905
Used in Stand Mixers.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
Removed four screws to remove main cover. Removed four more screws to remove fractured plastic gear housing cover. Removed retainer ring and slid two gears and dowel off main shaft. Lifted out remaining gear train and bearings, Removed all grease and metal chips from all components. Greased new gears and reassembled. Replaced plastic gear housing cover with oreviously purchased die cast replacement part. Assembled main cover.
Help other customers find the most helpful instructions.
Were these instructions helpful?
I investigated the problem by opening the mixer (four screws) and examining the gear box. Two gears were stripped. I ordered them, using the parts diagram provided. They arrives in about two days. I disassembled the gear box, cleaning out all grease and inspected for further damage. The gears and housing were completely cleaned with solvent. The transmission was then reassembled and regreased with food-grade grease. The mixer is now reassembled and working well. I was very pleased with the price and simplicity of my repair, versus taking it to a repair shop.
Very happy to find that the new gear housing was metal, not plastic. The whole problem was poor design of plastic to hold metal gears. Removed housing held down by four screws, removed two gears that were damaged. Retaining ring was difficult to remove from retaining slot. New gears replaced the old ones, new retaining ring put in place, new grease packed into all gearing, new stronger metal housing put in place and the Kitchenaid industrial mixer is better than new. Very happy with the parts I purchased.
sat on the kitchen table and with a screwdriver started to disasemble the mixer,hardest part was taking snap ring off (easy after you buy snap ring pliers)as gears were lifted off noticeable wearing was present on all parts. the bearing housing on the gearcase was broken lose, the only major expense. the other parts are not expensive so i decided to renew all parts. glad i did felt proud of myself when job was done. would do it again Joe
Removed rear band screw and bandremove 4 screws from head assembly and remove mixer headremove 2 screws fastening speed control switchremove 4 screws from gear box coverremove cover and slide out bevel gear and replace remove retainer ring and slide gear off shaft.reassemble in reverse order, apply grease to gear teeth.first time 25 minutes to inspect and reassemble2nd time 5 minutes to teardown,replace parts, and reassembleAll manufactured assemblies should be this nice to work on.
The parts I received from PartSelect were higher quality than the original parts. The bevel gear and housing were originally plastic. The new ones are solid metal. The machine sounds and runs better than it ever did. The drawings from the website made this really easy. This will be my first choise for parts from now on.
Unscrew the top and remove it , 4 more screws to remove the top of gear box , wipe out the old grease , lift the gears , but to remove the center gear you need a special narrow tip plier to remove the snap ring . Changed the center gear , apply new food grade grease and with reverse order putting back all remaining parts . Worked fine .
Removed old housing, pulled spring clip, slide on new gear and replaced clip. Put on new gasket and housing. Replaced outer cover. Done.
Removed 4 screws on mixer top. Removed 4 screws to gear box cover. Ordered replacement gears from Parts Select. Removed snap ring. Repaced two gears. Applied gear grease, replaced snap ring & screws. Gears at local appliance dealer were $39 each. Total parts from Parts Select + shipping under $20, received in 3 days!
The worm gear was defective. Called the 888 number and received excellent service. Said I would receive a refund and a new one in the mail.
remov5 screws then snap ring thenn 4 screws then reploace with new parts and put back together
Replaced cracked plastic gearcase/transmission with new medal one and replaced hub bevel gear attachment, bevel gear and gasket.
Remove screw at back of mixer,remove metal sleve and remove three more screws (front and sides. remove screws and plastic cap of gear box then remove holding ring in post and remove damaged ring installation is opposed of removal.
Took screw off band. This revealed 4 screws to upper housing. Removed 4 screws and lifted upper housing off . To my surprise I found no screws holding gear housing cover in place. You could tell they were there at one time. Should be 4. I removed cover disasembled what was left of gears. Cleaned old grease ordered parts. Thought since there was only 1 screw on diagram it would ship 4. No big deal. After recieving parts further inspection revealed no screws holding motor in place. This blows me away. Anyway off to local hardware store for more screws. Got home slapped it togethere in 10 minutes. Ordered this off TV about 6 years ago. They must have had it in for repair and forgot to put it back together. All that aside it runs better than ever. Thanks much Michael
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.