Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS11746830
This door gasket can be installed by simply pressing it into the channel around the door.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
Took out about 7 torx screws to remove the inner door liner. Discovered evidence of leak coming from the sop dispenser latch, and noticed the grommet had turned soft and was torn. The grommet is only about 1" square. Used nut driver to remove two screws to remove latch assembly. Slipped old grommet off and put new one on, and reattached the latch. The foam seal at the bottom of the door looked worn, so we replaced it with weatherstripping from home improvement store. The main door seal was brittle, so we replaced it too - just grab an end and pull the old one out. The new one was installed by starting at one end and we just pushed it in place. We used a nut-driver to push it in - we were afraid a screwdriver might damage it. The new door seal required us to latch the door to get it to stay closed the fist couple of days, but now it has loosened up a bit and works as expected. And NO MORE LEAKS. Cost is much less than a new unit!
Help other customers find the most helpful instructions.
Were these instructions helpful?
After dissassembling the unit to discover the leakage source I determined that it would do best to replace the top three contributors to the problem as listed by you. Disassembly, parts replacement and reassembly was straight forward and a few hints garnered from your good instructions and assembly blow-up drawings made the job simple with the most difficult task being the removal of the adhesive foam gasket at the bottom of the door's interior. After scraping as much of the deteriorated foam away as possible with a plastic scraper I used some of my wife's nail polisher remover and a clean-up rag (being careful not to get the remover on plastic parts)and soon I had the adhesion area surface clean and ready to receive the new seal. With close attention to clean up of residues left behind from detergent and water and care taken with part installation and reassembly it no longer leaks and I hope to get another 10-15 years of leak free operation out of the dishwasher
My dishwasher was leaking a small amount and it seemed to be happening during the last half of the cycle. The insulation at the bottom of the door was wet but not directly under the dishwasher by the motor etc. I tried the door gasket which was a simple 2 minute job but that didn't solve the issue. I took apart the door by removing the seven torx head screws on the inside (don't worry about the metal pieces on the sides with the phillips screws). I could see some white powdery build up and watermarks coming from the soap dispenser area. I thought maybe there was crack in the door. But after taking out the solonoid (it just snaps in and out) I could see light around the little latch that holds the soap dispenser door shut. I tried a bit of caulking but it just fell out after a day or so. Then I found the little grommet on PartsSelect.com. You have to take off a white plastic cover that covers the door latch mechanism - it snaps in and out on one point. A couple screws hold the plastic assembly in place. You can just remove the whole assembly, it doesn't need to be taken apart. Remove the old grey gasket around the latch and put the new one over the latch. It's more like a "boot" like around a shift lever in a car. Put the assembly back in with the latch going through the hole. Make sure the gasket covers the hole. Tighten the screws down, not so much as to tear the gasket but enough to be snug against it. Snap the white cover back on. Snap the solonoid back in place. Put the door back in place. Put the seven screws back in. You're all set - no leaks. The key to troubleshooting was that it started leaking during the rinse cycle after the soap dispenser latch had flipped up exposing the worn boot around the latch.
Using the pliers, my husband pulled out the old gasket to get it started. He then pushed the new gasket in with his fingers and used a screwdriver to press in the ends. That's it. Pretty easy. I ran the dishwasher a couple of hours after he installed it and there were no leaks. Still not leaking. Seems a bit quieter since the sealis better.I was secretly hoping for a new dishwasher eventually. But it makes much more sense to shell out $43 for the gasket rather than spend the $600 or better for a new dishwasher! I found the website very easy to use as well. Everything shipped quickly and there were no problems at all. I will bookmark this in favorites should I need it again!
I originally thought the door gasket was leaking so I went to partselect on line to order the gasket. After seeing the repair story results, I also decided to order the soap dispenser grommet also. I first relaced the door gasket as that takes about 5 minutes (take the easy way first right,) I was wrong as it still leaked. I then took the 7 torx head screws off from the door and the inside section just lifts off exposing the underside and the real problem. The soap latch had been leaking and was obvious from the dried soap/water trail. You have to remove two small screws and the whole unit comes out very simply. I took the extra time to clean off the build up of soap and hard water before replacing the seal and remounting the soap dispensing latch assembly. Ran another load and no more leaks! Thanks for the advise and the really simple but accurate way to order parts. I will use this site if I ever need any other parts. Very helpful and quick deliver as well as reasonably priced.
Observed the way gasket was installed including slight overhang on each side.I simply pulled out the old gasket, starting at one end. I then wiped down the area with a dampened rag and pressed in the new gasket exactly the way the old one came out. It is important not to stretch it, just push it into place ending up with the same overhang on both sides. Total time less than 5 minutes with no tools.
removed the door gasket by just pulling it out and pushing the new one in its place. very easy, took five minutes at most. Then removed the 7 screws holding the inside of the door in place, removed the dispenser assembly, held by two drive screws and replaced the dispenser door latch grommet. Finally, removed the insulation foam gasket. Had to scrape the old adhesive from the door as the old a\gasket had disintegrated. This took the most time. Then just pressed the new foam gasket in place. Reading the comments from others was a big help. Don't think I would have replaced the dispenser grommet had I not been warned about it. I'm sure it was part of the problem. All is well now, no leaks.
This ended up to be a (2) phase project. The first repair was to replace the door seal and inner door foam. Thanks to earlier online comments this part was really easy, but we still had a small leak. When I had removed the interior face of the door panel to replace the inner door foam, I had noticed the insulation was wet and deducted that the 'soap cup door latch gasket' was the real culprit so I had to place a second order (Phase 2). The order came quickly and in time for next Saturdays to to list. My advice is to replace all 4 items at the same time and save on mailing cost and repair time; reservoir O-ring, soap cup door latch gasket, inner foam gasket and door gasket. net repair time, about an hour start to finish.Don and RosieRochester, NY
Use towels to catch water that spills from unit. Lay unit on side to expose bottom. Remove plastic retainers, rear wheels, and bottom cover. Disconnect inlet and discharge hoses. Tie pull cord onto each hose separately. Temporarily re-install rear wheels. Set uinit upright. Remove two star screws from underside of wooden top. Slide top forward to release and remove top. Remove tie strap holding hoses to inner bracket. Lay unit on side again and pull hoses out. Remove discharge hose first to allow removal of inlet hose from plastic housing on back of unit. Tie pull cords to new hoses. Pull new hoses into unit. Reconnect hoses. Turn unit upright. Replace tie strap on bracket with new hoses. Hoses are marked as to where they should be secured to the bracket. Replace top. Remove old door gasket by pulling from one end of gasket. Clean gasket groove. Push new gasket into place. Close door to seat gasket. Remove and replace faucet adapter kit. Run unit and check for leaks. Lay unit on side, remove rear wheels, replace bottom cover and plastic retainers, reinstall rear wheels.
After performing some maintenance to get the water flowing properly through the system (that's another story) the door was leaking very badly during any test run of the dishwasher.We thought it was the gasket because the old one was calcified and dried out from years of harder water.We ordered the new one and in minutes after receiving the new gasket we had a firm seal and our dishwasher was back in action.
Thanks to repair stories about door leaks on partselect.com I ordered parts for the detergent/rinse dispenser in addition to the door gasket. The installation of the door gasket is really easy, simply remove the old gasket starting at one end. I needed a small screwdriver to get the old gasket end out of its channel, then pulled the entire gasket out. I cleaned the channel with water and simply pushed the new one into the channel, starting at the left bottom and continuing around. It is important not to stretch the gasket and also to have it equal length on both sides of the tub. Total time less than 10 minutes.The replacement of the detergent grommet requires removal of the inner door panel. I removed the seven torx-head screws along the edge of the plastic panel and lifted the panel away from the outer metal door. There are wires attached to the detergent cup motor. I tried to remove them but found it was easier to simply snap the motor out of it's retaining clip, leaving the wires attached. The inner door panel can now be removed. The detergent/ rinse aid module is removed by taking out two hex-head screws. It lifted away from the door and the grommet is right on the front, surrounding the detergent cup latch. I removed the old grommet, cleaned the residue of old detergent and water hardness from the latch and the backside of the inner door. and placed the new grommet over the latch. I used a little water on the new one to make it slide on easier. I then reattached the module to the inner door. Be sure the grommet is centered in the square hole and evenly tighten the two hex-head screws. Re attach the soap motor by snapping it in place being careful to align its plunger correctly with the soap module. There is a groove in the plunger that fits into the plastic arm of the module. Re assemble the inner door and tighten the torx-head screws evenly. This job took about 30 minutes and completely solved the leak problem.The broken spring linkage requires partial removal of the dishwasher. First, I turned off the power and water as a precaution. I removed the undercounter philips head screws, removed the lower access panel and kick plate using a nut driver. To access the door spring mechanism, the dishwasher must be pulled out from the cabinet about 10 inches. I had flexible electric and water lines so they didn't need to be disconnected. If the water and electric are rigid, then they have to be disconnected. This may require a professional. The replacement of the door springs and linkages is very easy once the dishwasher is pulled out. Keeping the door closed and locked, simply hook one end of the spring on the linkage, attach the other end of the linkage to the door and attach the other end of the spring to the hole in the dishwasher base where the old spring was attached. It is a good idea to replace both springs and both linkages to keep equal tension on both sides of the door. Slide the dishwasher back to it's original position and replace the undercounter screws and the lower access panels. Total time less than 15 minutes.
We simply removed the old gasket which was corroded, cleaned up the hard water buildup, and popped the new gasket into place. The problem was fixed! No more leak!
I first changed the dispenser door latch grommet, which was very eazy except for the left side nut screw which was a little awkwaed to get to with the nut driver. Not a big problem but difficult enough that i stripped the threads (plastic) and had to get a larger screw which is working fine so far. Since the grommet didn't stop the leaking although it was obvious it was leaking from the soap trail. I ordered the gasket and got it very promptly put it on and guess what. Still leaked some. I discovered when they installed the dishwasher the door appeared to be warped. To fix this there are two door tension springs under the bottom panel. By adjusting these with a log screw driver problem finally solved.It is good to have not only a great place to get parts but the idea's from others are terrific. Although this washer is 15 years old it looks new and now acts new. Thanks so much for good service and advise.
Removed two lower panels using nutdriver. Ran washer through a rinse cycle, to determine for sure where leak was coming from (under door on left). Examined the door gasket and observed buildup of lime deposits and a general depression of the gasket through years of use, especially in lower portions. Removed the old gasket observing how installed. Cleaned out groove with Lime-away and toothbrush. Washed clean using water in a squirt bottle. Dried things out using paper towels, and then pressed new gasket into place, starting at lower left. Readjusted the gasket to fit precisely end to end. Shut door and ran a drip free load.
Removed the old gasket, without tools, and fit the new gasket into the space, making sure it was in the groove correctly all around, job done, works great. The ordering of the gasket on this site was easy and the shipping time was amazing, one day. Would use this company again, and recommend to anyone needing parts that wants to do repairs themself. I am sure saved a whole lot over hiring someone, and got the job done sooner also.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2016 , Eldis Group Partnership. All rights reserved.