Quick Question!

Have you ever purchased from PartSelect.com before?

11746384-1-S-Whirlpool-WP8557301-Timer - 60Hz
11746384-1-S-Whirlpool-WP8557301-Timer - 60Hz 11746384-2-S-Whirlpool-WP8557301-Timer - 60Hz 11746384-3-S-Whirlpool-WP8557301-Timer - 60Hz http://www.partselect.com/Schematics/Whirlpool/RZBFZOPP.gif

Timer - 60Hz

PartSelect Number PS11746384

The timer controls most of the operations of the washer: water level, tub filling and emptying, length of cycles, and cycle setting sequences.

This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.

This part fixes the following symptoms:

  • Timer will not advance.

Compare At

$154.58

You Save

$25.76

Your Price

$128.82
Order within the next 6 hrs and your part ships today!
Get this part fast. Average delivery time via regular ground: 1.8 days.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 3.4 / 5.0, 6 reviews What's this?
1-6 of 6
 

21 of 25 people found this instruction helpful

Parts Used:
  • Timer - 60Hz
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Pliers, Screw drivers
Customer: Rick from Littleton, NH

Washer would fill and stop, would not agitate; advance the cycles

First I went to the Whirlpool site and downloaded the illustrated parts list for this model (a PDF file).

Seeing the part number, I then ordered the part from PartSelect.com.

While waiting for the part I tried to research how to remove the timer knob, but none of the online help I found was correct- the knob does not unscrew, but is held in place by a black plastic "keeper" on the back of the timer. The removal instructions are printed on the timer.

When the timer arrived I unscrewed the 2 screws at the back and edge of the console panel. Then the panel lifts up and out, exposing the timer. I released the knob, then removed a small screw beneath the knob that holds the timer.

Then I unplugged the wiring harness from the timer and removed it. I then reversed these procedures and installed the new timer.

As it turned out, the problem was not with the timer at all, but rather a defective lid switch, which is also located under the console panel.

Once I replaced the lid switch (very easy), the washer worked perfectly again.

Despite my imperfect initial diagnosis, a very satisfying experience.

Thanks for the great service.

Rick

Help other customers find the most helpful instructions.

Were these instructions helpful?   

14 of 17 people found this instruction helpful

Parts Used:
  • Timer - 60Hz
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: Mike from West Point, MS

Washer would not go into the next cycle.

I went on the internet check out a couple of videos on You Tube on changing out a Whirlpool Washing Machine Timer switch, watched it and did what they did on the video and found out it was real easy to do, and I had no problems at all.I think any DIY person could do it with little or no problems plus it didn't take me but about 20-25 min. to change out the Timer Switch,plus you could save yourself a lot money on a service call.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

10 of 10 people found this instruction helpful

Parts Used:
  • Timer - 60Hz
Level of Difficulty: A Bit Difficult
Time to do repair: 1- 2 hours
Tools: Nutdriver, Screw drivers
Customer: peter from bethesda, MD

Washer full of water and won't cycle

I was looking for a repairman when I found your excellent website. Even with the advice from your share the stories it took almost an hour to get the control panel off the top of the machine. There were 2 sets of 2 screws and when I finally realized what sliding the panel forward toward the front of the machine meant it came right off. When I first replaced the lid switch (easy once the control panel was open) the machine still wouldn't cycle. My choice was replace the timer, call a repairman or buy a new machine. Replacing the timer was easy with the control panel already open but I had to buy a 1/4 and 3/16 hex nut driver to remove the timer. The whole repair including parts, shipping and tools cost $110. Without your diagrams and parts list I never would have had the guts to try this repair. Thanks.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

7 of 8 people found this instruction helpful

Parts Used:
  • Timer - 60Hz
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Nutdriver, Screw drivers
Customer: John from Wauconda, IL

Washer would not advance cycle

Tried different cycles, none advanced. Went online to find exploded view of washer top for removal information. Remove power plug from outlet! Removed a few screws and bolts, pulled plugs and the knob. Look around further instructions were inside. Then removed existing timer for part number specifics. Checked online - timer costs were close but shipping varied quite a bit. PartSelect had the best value. Received package next day. Installed and running within a half hour.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

5 of 7 people found this instruction helpful

Parts Used:
  • Timer - 60Hz
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Screw drivers
Customer: jorge from Miami, FL

The washer would fill up then it would stop and do nothing.

I follow the instruction that I read online. I open the back of the panel by removing the four screws then I took of a small screw that is holding the timer in place. I unpluged the timer from the conector and reverse the whole process to put it back together. I had never done any of this stuff but thank to your help and the forum I was able to save a lot of money

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 6 people found this instruction helpful

Parts Used:
  • Timer - 60Hz
Level of Difficulty: Really Easy
Time to do repair: 30 - 60 mins
Tools: Nutdriver
Customer: Dino from Brockton, MA

Clock stop working in the middle of cycle

Remove to screws from rear of control panel, remove the clock assemble, replace with the new one, and reinstall the control panel.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1-6 of 6