Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS11746115
***Please Note - If there is no display on the control panel, check the thermal fuse on board first before ordering this part.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
removed 8 torx screws and inner door panel. took off electronics cover, unplugged connectors & replaced circuit board. ran ok for two cycles, then failed to start again. Sears svc tech advised circuit board and the touch panel housing would have to be replaced as a unit. parts and labor $319. $65 svc fee paid, rcvd $65 coupon on new machine. Went in again and blew out ribbon socket connecting touch panel and circuit board. Now running OK. (??!) $100 for circuit board is good deal. Wasted $65 on svc call, to find out cost of authorized repair service was 50% of cost of new machine. We'll see how long it runs.
Help other customers find the most helpful instructions.
Were these instructions helpful?
My 10 year old Kitchenaid dishwasher began performing erratically:• It would not run a full cycle and would light the cancel light.• It would erroneously light the "child lock" light.• It would run the drain cycle and not stop.I "rebooted" / reset it several times by powering off and back on, but it after a couple "reboots" it would not reset.I checked the water sensor and the plumbing, pumps, and electronics visually but did not see anything awry.It appeared to be a logic problem so my diagnosis led to the electronic board.I ordered the board and received it very quickly (two business days).Installation was easy:1. Removed torx head screws on the top / inside of the door to release the plastic control panel & was careful removing it to avoid damaging the built in plastic brackets that hold it to the door. This was achieved by being sure all screws were out, then pulling the top of the plastic panel out away from the door. The "inverted V" shaped brackets pivoted and needed to be lifted off the metal frame on the door. Continue to support the panel and 2. Unplug the ribbon cable connecting control panel to board. Set panel aside.3. Unplug all wire connectors from board.4. Remove two 1/4" hex head screws that hold the board / backing frame to the door being VERY careful not to drop them into the door.5. Replace with new board / backing frame.6. Reconnect all wires.7. Reconnect ribbon cable and install front control panel8. Test9. Eureka!10. Wash some dishes...That's my story!
Symptoms: at first the dishwasher would wash the dishes but not stop at the end of the cycle. After several weeks of using a timer and opening the door during the drying cycle and getting an estimate of $421.78 to fix the machine (we declined) the dishwasher finally would not go thru its whole cycle. I reasoned it must be the Control Assembly and ordered one. to install it I removed the 8 "star" screws in the door, removed the inside of the door, removed the black, plastic cover over the Control Assembly, disconnected all of the connectors to the Control Assembly and the two anchor screws. The Control Assembly then was easily removed. The installation was done in the exact reverse of the tear down. After the door was reassembled the dishwasher has worked correctly for over a week. I saved about $320 by doing the job myself. I hope the machine operates for another ten years.
i unpluged the diswasher and killed the electricity to it. next i opened the door and took all the screws out and slowly removed the cover from the door.watch out this will make the door try to close on you. then i figured out it was not the control assmebly but it was the thermal switch. it did not have continuity. everyone had said it was the control board that is why i ordered it but found out it was the thermal switch which only cost about $10.00 so I ordered one and replaced and fixed the problem. Thanks parts select for letting me return the control module. that would have been a $100.00 dollars wasted. Next time I will learn it is not always the most expensive piece that breaks. Thanks again hope this will help someone else out.
Followed the video. Only issue was that the panel mount screws cracked the plastic nibs that the screws threaded into. I replaced the screws with a Chrome sheet metal screw a bit longer and it held. Easy job!
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.