Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing reviews that matched. Try using some different or simpler keywords.
★★★★★
★★★★★
Rick B - October 2, 2021
Verified Purchase
ok seller
ok seller
★★★★★
★★★★★
Michael B - August 12, 2020
Verified Purchase
Easy repair
Good quality
★★★★★
★★★★★
Karen D - June 8, 2020
Verified Purchase
Wrong part
Not sure if I ordered the wrong part or if the wrong part was sent by accident. I need the igniter/flame sensor for the oven (not the stove).
★★★★★
★★★★★
Dennis P - January 28, 2019
Verified Purchase
Quick and easy
It only took a few minutes to install the new spark igniter. Works great.
★★★★★
★★★★★
Tim W - November 18, 2018
Verified Purchase
Ordering and delivery went well
I was able to do a major cleaning in the area where the igniter sits and that solved my problem. I ordered five because I figured if I change one, why not all. I also took a file to the area where the gas feeds the igniter. I found there was a slight buildup of dirt. Enough to prevent gas from coming in contact with the igniter. The screws that hold down the burners are crap and rusted through. I had to drill, tap and install new screws.this is a huge flaw. I paid $1700 for this stove. You would think they could put in a respectable screw made out of an appropriate material.
★★★★★
★★★★★
Nancy V - September 29, 2018
Verified Purchase
Repair
The repair went well no issues once we finally got the part not your issue it was Fedx that lost the part. Your customer service was very helpful in getting the part reshipped.
★★★★★
★★★★★
Christian R - September 28, 2018
Verified Purchase
Works, difficult installation
Part arrived very quickly, however not a direct swap without help. The bracket that holds the ignitor is too short to mount the screw. Had to Dremel out the hole to increase its length by about a sixteenth of an inch. Went back to make sure this was the proper part and it was so this is just poor manufacture. But it's in and works fine.
★★★★★
★★★★★
Allen W - February 7, 2018
Verified Purchase
Great Service and Correct Part
The first part I received to fix my oven burner was the wrong part. PartSelect quickly sent the correct part for my repair, and even more quickly refunded the cost of the first part and and shipping. The customer service rep was a pleasure to work with.
< Prev
1
Next >
Customer Repair Stories
Average Repair Rating: 2.2 / 5.0, 5 reviews.
What's this?
Sort by:
< Prev
1
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing installation instruction that matched.
Whirlpool gas stove burner igniter had broken.
Our existing gas stove burner igniter had broken on one of the four burners. I therefore obtained a replacement igniter and mounting screw form PartSelect.com which were indeed perfect replacement parts. However, I could not remove the burner plates from the top of the stove since they were basically welded into position by years of heat.
... Read more I therefore followed instructions as submitted by a previous customer (thank you Michael of Bloomington, Il), snapped open the stove lid retainer clips, and then lifted the stove surface about 4 inches. Through that opening I was able to reach the underside of the involved burner. Unfortunately, I could not unscrew the existing broken igniter mounting screw and therefore had to break off the already broken igniter and grind down the remaining mounting screw using a drill grinder since the screw was basically welded into place. Once I did that, I was then able to install the new igniter using a separate unused screw hole already in place right beside the old previous mounting screw. With that done, the new igniter works perfectly and the burner works just like new. It was however a lengthy process over two hours long because of the glitches described above. Nevertheless I'm very pleased that the parts were perfect and the repair is complete.
spark igniter was weak and not lighting the flame.
Open top oven door and remove the 2 front screws which hold the burners and controls to the frame. DO NOT lift the burners more than an inch or so to look inside. You WILL bend the gas lines in the back if you do. Pull out stove from the wall, shut off gas supply and disconnect hose if needed to have room to work. Remove top back panel an
... Read mored remove the 3 wires connecting the top burner assembly and also remove the 2 gas lines. Now you will be able to remove the burner assembly safely. Flip it over and try to unscrew the screw holding the igniter. When you fail, drill it out and get a small metal screw to replace it. The metal is soft and the screw is hard, so drill carefully. The rest is easy, put in the new igniter and screw. and put it back together.
Read less
Daniel from Needham, MA
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers, Wrench (Adjustable), Wrench set
38 of 52 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Replace 2 ignitors and 1 ignitor switch
I must admit that I did not do this. A neighbor who has electical experience did the job.
The screws that hold the ignitors were too corroded to reuse. It required drilling new holes and taping threads. If self-taping screws were included it would be easier to replace.
The switch was much easier to replace with f
... Read morelare nut wrenches.
I took out the old and replaced with the new. The hardest part was getting that tiny halogen bulb in that tiny little hole. It took longer to take the oven racks out and put them back in than to make the repairs.
Having no manual nor finding any instructions online, I spent a while trying to figure out how to safely get to the ignitor mounting screw under the range top. I popped the snap clips on either side of the stove to loosen the top and pulled the top up a few inches to see why it was being difficult to raise. It turns out that the gas pipin
... Read moreg was solidly attached from the controls to the burners and I was slightly bending the tubes as the top was raised. The tubes have angles and curves to "accept" the bending pressure I was applying, so it looked like I was doing the right thing. In case I was not doing the right thing, however, I raised the top only enough to get access to the ignitor base and mounting screw. Then the fun began as the screw would not loosen. After several attempts using liquid wrench, tapping on it, etc., the screw head finally just broke off. Uh-ohhhh. Not to worry, however, as there was an empty mounting hole right next to the old one that appeared to be able to work. The mounting screw for the new ignitor was backordered, so I tried a couple dozen different screws I had in my toolkit and finally found one that would fit width-wise, but I had to nip off some of the length to get it to seat properly. The replacement ignitor also had a different width blade connector than the original so I had to grind away some of its width to reattach it to the lead wire. If I had a different sized blade receiver, I would have instead replaced the receiver on the end of the lead wire. It took about 90 minutes in all.
Read less
Michael from Bloomington, IL
Difficulty Level:
A Bit Difficult
Total Repair Time:
1- 2 hours
Tools:
Pliers, Screw drivers
28 of 38 peoplefound this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
< Prev
1
Next >
Questions and Answers
Ask our experts a question about this part and we'll get back to you as soon as possible!
19 questions answered by our experts.
Sort by:
< Prev
1
2
Next >
Search filter:
Clear Filter
Your search term must have 3 or more characters.
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Sorry, we couldn't find any existing answers that matched.Try using some different or simpler keywords, or submit your new question by using the "Ask a Question" button above!
John
November 7, 2017
(1) When I turn the left front power burner control knob to 'ignite" position the igniter for the right rear "accusimmer burner sparks instead. (2) my wife says it seems to take to long for anything to heat up; even on the power burner. Suggestions?
For model number SF387LEKT0
Hello John,Thank you for your question. I would suggest checking your spark module then. You should be able to test it with a multi meter to see if the part is still working. Good luck with your repair.
4 people found this helpful.
Was this helpful?
Thank you for voting!
Michael
September 12, 2019
How do i lift the top off to get to my ignitors. I can actually see the porcelain is cracked. Could you be so kind and tell me my part#also
For model number MGR6775BDS
Good Day Michael. Thank you for your question in regards to your unit (Model Number MGR6775BDS). Here are the steps to replace the igniter: 1) Unplug the unit or make sure the circuit breaker is turned off before starting any repair. 2) Tools Required to complete repair: Strap Wrench, Flathead Screwdriver and Phillips Screwdriver. 3) Remove Grate. 4) Remove Seal Gas Burner Hand but turning counterclockwise slightly (Use strap wrench if not able do this by hand). 5) Using the flathead screwdriver remove wires from burner head. 6) Using Phillips head screwdriver remove the two screws that are holding the old igniter to the burner head. 7) Insert the new igniter into the burner head and re-thread the screws. 8) Reconnect the wires. 9) Reinstall the burner head and turn clockwise to lock. 10) Place the grate back on. The Part Number for the igniter that is compatible with your unit is WP8523793. You can order this part either online at our website www.PartSelect.com or by calling us by phone at 888-260-4310. Best Regards.
4 people found this helpful.
Was this helpful?
Thank you for voting!
Sooren
March 12, 2018
How do i replace this part?
For model number GLT3615LQ0
Hello Sooren, thank you for your question. I checked your model number for installation instructions for this part. Unfortunately, this part WP8523793 is not listed as a compatible part on your appliance. The surface igniter replacement for your model comes with the burner head assembly. Depending on which surface igniter you needed to replace, you would want to order per your model information, and those parts are as follows: Top Burner with Spark Electrode PartSelect Number: PS389259, Top Burner with Spark Electrode - 12K - Right Rear PartSelect Number: PS389260 and Top Burner with Spark Electrode - 6K - Right Front/Left Rear PartSelect Number: PS389258. I hope this information helps!
3 people found this helpful.
Was this helpful?
Thank you for voting!
Donald
September 27, 2019
I have ordered part # ps11746068 spark igniter for this cooktop. I don't have a repair manual for this cooktop and the parts schematic shown on your site don't indicate what the process should be to replace this item. Are the burner heads attached to the top or are they screwed into the burner body. Do i just have to remove the burner head (attached by two screws) to replace the igniter?
For model number MGC5430BDW
Hi Donald, Thank you for your question in regards to your unit (Model Number MGC5430BDW). Here are the steps to replace the igniter: 1) Unplug the unit or make sure the circuit breaker is turned off before starting any repair. 2) Tools Required to complete repair: Strap Wrench, Flathead Screwdriver and Phillips Screwdriver. 3) Remove Grate. 4) Remove Seal Gas Burner Hand but turning counterclockwise slightly (Use strap wrench if not able do this by hand). 5) Using the flathead screwdriver remove wires from burner head. 6) Using Phillips head screwdriver remove the two screws that are holding the old igniter to the burner head. 7) Insert the new igniter into the burner head and re-thread the screws. 8) Reconnect the wires. 9) Reinstall the burner head and turn clockwise to lock. 10) Place the grate back on. The Part Number for the igniter that is compatible with your unit is WP8523793. You can order this part either online at our website www.PartSelect.com or by calling us by phone at 888-260-4310. Best Regards.
2 people found this helpful.
Was this helpful?
Thank you for voting!
Don
September 27, 2019
I recently asked a question about installing part #ps1174606 surface burner spark igniter in a Maytag counter top ( mgc5430bdw) and followed the instructions received, they apparently don't apply to this model top. The burner head is held in place with two screws and while i can wiggle the burner head against the slack of the screws, i can not move the head any further either cw or ccw by hand or with a strap wrench as instructed. Aside from drilling the heads off the screws ( the screw drive is rusted/burned) is there another solution.
For model number MGC 5430 BDW
Hi Don, sadly you would have to remove the screws, I do not know of anyway around it. Thank you for your question and good luck with your repair!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Mike
May 10, 2019
When one burner is turned on and ignights the spark ignighter on the other burners will continue to flash for several seconds (20-30) before eventually turning off.
For model number CVGX2423
Hi Mike,
Thank you for your question. A normally functioning igniter will typically click up to three times before it sparks. But, every now and then you may run into instances where the ignitor continues to click or tick even after the burner is lit, or the burner never lights at all. A clicking ignitor typically is not dangerous and may continue to click if the gas is shut off.
One of the most common sources of this issue is that the Burner Cap is out of place. Make sure the cooktop is completely cooled and remove the Burner Grate to access the cap. Try removing the cap and center it on the base. If the burner cap is askew, it can prevent the burner from lighting.
If that doesn’t work, check for moisture. If you recently had a pot boil over on burner, a food or grease spill, or cleaned the cooktop, there may still be moisture present even if it looks dry. Remove the burner cap and give the burner time to air dry. To speed up the process, make sure all the burners are off and towel off the top of the range. You can then either use a fan aimed at the range top or set your oven to 350° and leave it on for around 30 minutes to speed up dry time.
If you see that there is debris stuck in the holes in the burner, that could also potentially be the culprit.
You can use a metal pin or paper clip to clear the debris out of the grooves. Never use items such as toothpicks to do this, they may break off and get lodged inside.
If you get through all of these tips and still have the clicking problem, it may be the Spark Module, Spark Ignition Switch or the Ignitor itself. You can find replacements for your model stove for purchase on our website. If you feel comfortable, this is a repair you can do yourself. But, if you’re ever unsure don’t hesitate to contact a technician and consult your owner’s manual. I hope this helps. Thank you and have a great day!
2 people found this helpful.
Was this helpful?
Thank you for voting!
Adolf
August 27, 2019
How to replace front left burner ignitor and is the part# and where can i get it
For model number Maytag Propane Gas Cooktop#MGC5430BDB
Good Day Adolf. Thank you for your question in regards to your unit (Model Number MGC5430BDB). Here are the steps to replace the igniter: 1) Unplug the unit or make sure the circuit breaker is turned off before starting any repair. 2) Tools Required to complete repair: Strap Wrench, Flathead Screwdriver and Phillips Screwdriver. 3) Remove Grate. 4) Remove Seal Gas Burner Hand but turning counterclockwise slightly (Use strap wrench if not able do this by hand). 5) Using the flathead screwdriver remove wires from burner head. 6) Using Phillips head screwdriver remove the two screws that are holding the old igniter to the burner head. 7) Insert the new igniter into the burner head and re-thread the screws. 8) Reconnect the wires. 9) Reinstall the burner head and turn clockwise to lock. 10) Place the grate back on. The Part Number for the igniter that is compatible with your unit is WP8523793. You can order this part either online at our website www.PartSelect.com or by calling us by phone at 888-260-4310. Best Regards.
1 person found this helpful.
Was this helpful?
Thank you for voting!
Robert
June 25, 2021
how to find model no. all i have is booket.
For model number mgr6775
Hi Robert,
Thank you for your question. If your range has a bottom drawer where you store pots and pans, pull the drawer out and you will find the label with the model and serial numbers either on the left or right frame that the drawer shuts onto. You may also find it either behind the control panel if it is a gas oven, behind the fuse cover, underneath the cooktop (if it is a lift-up style), under the front surface unit, on the frame of the broiler section, on the door frame, on the exterior of the unit or the interior side panel. We hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
Dexter
May 5, 2018
Trying to replace a broken igniter for left rear surface burner is this correct part so a screw come with this
For model number 665.72133300
Hello Dexter, thank you for your question. Yes, the Surface Burner Spark Igniter Part number WP8523793 is the correct part. The screw is a separate part number, which is Screw, Igniter Part number WP8273062. Good luck with your repair!
1 person found this helpful.
Was this helpful?
Thank you for voting!
William
January 10, 2019
Where is the igniter harness for the top burners igniters located and how do i gain access to it i have checked the sketches the do not help me
For model number JDR8895AAS
Hello William, thank you for your question. The spark igniter harness mounts on the burner valve stems. When the gas burner valve knob is depressed and turned, this part creates a spark that lights the gas and starts the burner. To access these parts follow these steps to lift the maintop and replace the parts. 1. Disconnect power before servicing. 2. Remove surface burner control knobs by grasping knob and raising knob straight upward. 3. Remove screws securing infinite switch bracket to maintop. 4. Remove screws securing burner assemblies to maintop. 5. Remove screws securing maintop to chassis. Screws are located in the front left and right corners with the upper oven door open. 6. Remove screws securing ground strap to chassis. 7. Raise and remove maintop from unit. 8. Locate switch and replace 9. Reverse procedures to reassemble. I hope this helps!
1 person found this helpful.
Was this helpful?
Thank you for voting!
< Prev
1
2
Next >
✖
Ask a Question
Ask our experts a question on this part and we'll respond as soon as we can.
