Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS11745959
This thermostat has an internal heater L155-25F. This thermostat controls the internal drying temperature.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
First removed front and drum to check gas valve and igniter. No gas, no ignition. Checked power to devices; none (check hot line to ground, not to neutral.). Removed back of control panel looking for a relay or something. Found none, but did find a wiring diagram. That is where the site really came in handy. Studied wiring diagram together with the exploded view and pictures of each part to come up with a troubleshooting plan. Took the back off as well as a cover inside. Tested each part with meter, again going to ground and not across the device. Of course, the final device before the gas valve, a one time thermal fuse, was the bad part. At first assumed just a bad part. Later wondered if fuse did it's job and another part was bad. Ordered and installed new thermostat just in case. Put everything together after a complete cleaning and everything is fine so far. Not a particularly hard job because I had the wiring diagram and access to parts select site. Would have been much harder without them. Took a long time because almost the entire dryer had to come apart. But it got a good cleaning because of it and found a couple of bucks in change to help offset the cost. Can't imagine what a service call would have cost.
Help other customers find the most helpful instructions.
Were these instructions helpful?
Once the coils for the gas valve got hot they failed and shut the gas vavle off, we ended up changing the coils which fixed the problem but part select held up there end of shipping out these parts which we could not get localy. so if your dry ignites some time and or not for long its either these coils or the cycling thermostat which will casue the same conditions because the the cycling thermostat controls the coil. good luck!
after reading your site reviews I bought all 3 thermostat's. It took about 30 minutes (with a coffee break) to change them all out and that saved me $400.00. I popped the lower front pannel off and all three thermostat's were accessable from there. i needed to remove the lent trap and tube which is held on by 2 screws to access the thermal fuse and cycling thermostat. there was a lot of lint trapped in the tube. it was a few screws and some spade connectors. very easy repair. as I said above buy all 3 and it saved me $400.00.
PartSelect.com rocks! Watched the online videos and did what he did. Labeled wires so that I wouldn't switch them when re-connecting new parts. Although only the fuse may have been bad, I decided to replace the cycling thermostat as well, since others implied that they work in concert, and a defective thermostat could have triggered the fuse failure. Also, looked outside and saw that landscapers had recently piled mulch all the way up to dryer vent. (Could this have caused the parts to fail?) So for less than $45 (parts + standard shipping), the dryer works like new. Happy wife makes happy life.
First watched a youtube video on the process. Took off front cover. I'd already replaced a belt so I knew what to expect. Two screws holding the retaining plate on top of Coil Valves (both). One screw was a bit seized, so a bit of persuasion w/ the pliers was in order. There was no info on which way up, but luckily I noticed a bump on each valve, and two matching holes on the retaining plate. (Note to others trying this) Of course while re-assembling a dropped and temporarily lost a screw, then one of the machine screws that hold the front cover on, but other than my stupidity, and frustration that job was easy. The cycling thermostat I just got "just in case". I knew the main thermostat was working, but couldn't accurately check this one, so I got a spare and replaced it. I'm sure it was one of the valve coils as I'd read another user had an issue where the coil would work fine at first, but after it got hot would not work. After a cool down, it'd work fine again. So all in all, easy job.
After replacing many, many parts the dryer still does not work! Replaced Thermo Fuse, Thermostate, Cycling Thermostat, Coils, Ingition Sensor and Ignitor. Ran meters across all incoming power, timer control, ignitor power, etc. all check out according to schematic. Incoming gas supply is functioning. So, 6 parts recommended later still same problem. On the good side, all parts were shipped out very quickly. Highly impressed with service.
Watched video. Walked right through it.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.