Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS11744741
This power nut is intended for use with trash compactors.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
Pulled compactor out on a piece of cardboard. Used socket set to take top off and evaluate the problem. Power nut was not holding on one side. We ordered two power nuts. Decided to repair only the unlevel side. Fast and easy and cheaper than a new compactor. Whirlpool compactor is 28 years old and working like a charm. Thanks for the diagram and accessibility to parts.
Help other customers find the most helpful instructions.
Were these instructions helpful?
I slid the compactor out of the cabinet space it sits in and unplugged it. I removed the two screws that hold the control plate on and it then lifts up and off to reveal the screws that hold the top down. Then I removed the two screws that hold the top of the unit on and removed the top. I then put the switch plate back on and plugged the unit back in and ran it so I could see it operate from above. It went all the way down compacting the drawer but kept running and did not reverse and come back up. I figured it was the directional switch and ordered that. The plastic power nuts that the unit rides up and down on looked worn so for $10 each I ordered a pair of them also. The parts arrived in 3 days. I decided to install the power nuts first. When I removed the metal casing that holds them I saw that wings on the plastic power nuts that hold them in place in the metal casing were all broken off. I installed the new power nuts then plugged it back in and ran it. It cycled perfectly. luckily I had not opened the directional switch and I was able to return it to Partselect for a refund. In total I had to remove and reinstall 4 very short screws and 4 small bolts. While I had it out and apart I also cleaned out quite a bit of old trash that had escaped to unseen parts of the compactor. It is 26 years old and working fine. I don't think they make them like they used to. Thank You Partselect for a great experience
I removed the compactor from under the cabinet and unpluged it from the power supply. The ram was in the down position and wedged to one side . The lower side was the broken power nut side. I first removed the good side nut retainer cover and turned it down to a level position before removing the defective power nut cover. Then I went on Google search, got lucky and found PS Parts select's web site. I was Greeted by a very pleasant and knowledgeable clerk named Lacey. I described the part I needed, and gave her the model, serial numbers. She found the part , told me the price, I ordered 2 new ones and they arrived at my home in 3 days as she said they would. Exact Fit. Screwed them on the two power rods, put the covers back on and re-installed under my cabinet, and SHIZZAM !! Back in business.
double oven remove 4 screws and pull ovens out. rest on support crate etc. replace spring.
I removed the unit from under the counter. After removing all of the bits of old trash and making sure the chain and gears were not slipping or striped, I knew it was the power nuts on top of the ram. After all of these years they were worn out, almost smooth inside where the threads are. They were easy to locate on your website. I received them in 2 days (faster than expected) and in 10 minutes the unit was back together and working well. Today was the first bag to be taken out after the repair, it is much heavier than the previous ones, a sign that we are now packing much more trash in a single bag!
Removed drawer first, then removed compactor from under kitchen cabinet. Removed top cover. Discovered that a small wash cloth was wound around one of the drive screws. I then removed plunger and put it back in position. Replaced top cover and turned on compactor. Plunger went to the top and made a grinding sound. I removed the cover to discover that when I put the plunger back in, I did not have the lever that trips a micro switch in proper position. I needed the replacement plastic gears that were ruined when compactor did not shut off. Relatively easy job if I had noticed the location of the shut off lever, and would have needed the parts.
I held up on the compactor ram as i loosened the two screws on each of the two retaining cups. I then unscrewed the threaded bushings and lifted the ram out of the unit. I then cleaned the surface of the tracks on which the ram guides up and down and applied a thin layer of silicone grease to those surfaces as well as the threaded rods. . I placed the ram back into the unit and held it in place as i replaced the threaded bushings and their respective caps. Unfortunately i neglected to move the limiting switch that stops the ram when it reaches the top of the cycle and I broke the lever that contacts the ram and subsequently activates the stop switch. so i removed the ram and removed and inspected the switch. It was broken beyond repair so i ordered a new switch from the same place I purchased the threaded bushings and am waiting for them to arrive. Lesson learned, pay attention to the sequence by which the original parts are removed and understand how the system functions so that you can remember to put it back in the right order.
Took of top housing; saw traveling compactor not properlly alligned. Removed cover from Power Nut; saw that it was stripped. Ordered new power nut. Replaced power nut & aligned traveling compactor. Replaced top housing.
The plastic power nut had stripped out on my 12 year old trash compactor. Ordered 2 new ones from Partselect and installed them. Now it works like new again.
Removed unit from under counter. Moved to garage. removed Top, Bottom plates, and switch controller. Turned upside down and removed power screw nuts One came off easy. One side frozen. Took large pliers and worked nut off of drive screw. Removed ram. Ordered two new power screw nuts. Lubed screws, chain, nuts, rollers and cleaned whole unit. Straightened ram which was bent from so many years of use. Unit 26 years old. Replaced all plates and plugged it in. Works like a champ. Thanks for carrying parts for a unit this old.
Trash compactor was stuck, took apart to see the power nut stripped, ordered nuts and while putting the ram back in I didnt see the reversing switch lever and broke it off.Guess Ill order a new switch ($40)..moral of story...slow down and pay attention to the details..
replaced power nuts
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2016 , Eldis Group Partnership. All rights reserved.