Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS11744404
This bake element has push-on terminal ends.
NOTE: This element has been updated by the manufacture. New installation screws are required. Screws are sold separately.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
I shut off the breaker in the fuse panel for the range ( recommended)I had to unscrew the two mounting plates, unclipped two wire connectors.Reconnected the two wire connectors ( pull off, push on)DoneFlipped on breaker and was baking in less than 15 minutes.
Help other customers find the most helpful instructions.
Were these instructions helpful?
First off, I ordered the part to be delivered 2-3 business days. I ordered this online on Sunday, so I figured it wouldn't show up until at the earliest on Thursday. We got it on Tuesday. Fantastic. Once I got it I pulled the range out and unplugged it. Next I removed the two screws holding the old element in place with a phillips screw driver. Pulling the old element out carefully I removed the two wires from either end. Next I attached the wired to the new element and screwed in place. Fast and easy! Plugged the range back in and we were cooking.
repair was easy- turned off power at electrical box, emptied out the wire shelves in the oven. Unscrewed two fasteners holding element in place, pulled element out about 3 inches, unplugged electrical end connectors.Then got new part, attached two electrical connectors, slid back in place, fastened with two screws, turned power on and we're baking. I believe this part would be covered under my warranty- but we were having a party that weekend and I could not wait for the repair guy to do this on his schedule, plus his labor alone would have cost much more than my part and next day delivery.
unscrewed element from oven, traded wire connections to new element, screwed new element in - saved myself a $75 service call
I removed the two screws that held the element bracket in place. I then pulled the element out a few inches and disconnected the wires. I then reconnected the wires to the new baking element, pushed the wires back inside the oven and resecured the bracket. NOTE: turn off the power to the oven! I thought that since the oven was not on, I could safely perform this replacement...unfortunately I got zapped.
First I shut off the oven breaker, then I removed the racks and the oven door. I next removed the two retaining screws holding the element in place. I gently pulled the element forward to expose the blade connection. I disconnected the old element, attached the new element, slid it back into place and replaced the retaining screws. I remounted the door and turned the power back on. I did a test run on the oven. It worked perfectly.
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires...) One of the wires came off before i was able to pull the element out far enough. I then had to take the back off (2 screws) The total repair took about 5 minutes
Very easy, with only the removal of 2 screws.
My husband did it was really easy ,he turned the power off to the stove,took the back cover off the stove with a screwdriver and pulled the old one out,then he slipped the new one in connected the wires ,it took less than 15 minutes that simple.
Your site really helped out alot. Job was farily easy and now we have heat. Difficult part was reaching the wires in the back. Thanks again! TZak
Took out two screws in the back of the oven that held in the bake element. Pulled the element out of the back of the oven to expose the wires. Pulled the wires off the broken element and then reattached the wires to the new element, put it back into place. Reattached the screws. Done in less than five minutes.
Actually a very simple repair. Determined that the problem was a burned out bake element since broiler worked fine. Looked up part on-line...diagram on PartsSelect made this very easy.Ordered part selecting normal shipping (part arrived in 3 days). Repair: 1) turned power off at the breaker box 2) removed baking shelves. 3) removed the two mounting screws holding old bake element in place 4) gently pulled the bake element out of the oven until about two inches of electrical wire were exposed. 5) removed the electrical clips from the old bake element. This required steady wiggle to get them off. 6) attached the electrical clips to appropriate ends of new element ensuring they are well seated 7) pushed electrical wires back into the oven and mounted the element using same two screws. Turning the power back on at the breaker, I then tested the repair. No problems noted...turned oven off and replaced the baking shelves. Baked homed made bread that evening.
The process would have been easy except the wiring to the element had a problem. One wire was too short which meant pulling the entire stove assembly out to reroute the wire.The part worked fine; the problem was with initial wiring of stove.
Just followed the installation instructions offered on this website. WAS REALLY EASY!
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2017 , Eldis Group Partnership. All rights reserved.