Quick Question!

Have you ever purchased from PartSelect.com before?

11744404-1-S-Whirlpool-WP74010750-Bake Element
11744404-1-S-Whirlpool-WP74010750-Bake Element 11744404-2-S-Whirlpool-WP74010750-Bake Element 11744404-3-S-Whirlpool-WP74010750-Bake Element http://www.partselect.com/Schematics/Maytag/54971.gif

Bake Element

Compare At

$43.93

You Save

$7.32

Your Price

$36.61
Get this part fast. Average delivery time via standard shipping: 1.8 days.

PartSelect Number PS11744404
Manufacturer Part Number WP74010750
Manufactured by Whirlpool

This bake element, also known as an oven bake element, supplies heat for baking purposes. This part is located at the bottom of the oven. If you find little to no heat when baking, a burned out bake element, or food is taking too long to cook, these symptoms could be solved by replacing the bake element. Before starting this replacement, make sure the range is unplugged from the power source or shut off from the house circuit breaker. The tools needed is a Phillips screwdriver. For safety reasons, make sure to wear gloves.

This part works with the following brands: Maytag, Magic Chef, Jenn-Air, Crosley, Amana, Admiral, Kenmore, Norge, Whirlpool.

This part works with the following products: Range, Wall Oven.

This part fixes the following symptoms:

  • Little to no heat when baking.
  • Element will not heat.
  • Oven not heating evenly.
  • Will Not Start.
  • Oven is too hot.

Videos For installing this part.

Installation Instructions Provided by PartSelect customers like you.

Average Repair Rating: 4.5 / 5.0, 60 reviews What's this?
 

4 of 6 people found this instruction helpful

Parts Used:
Level of Difficulty: Easy
Time to do repair: 30 - 60 mins
Tools: Screw drivers
Customer: pete from tioga, ND

No oven heat -cook top cracked a while ago

the bake element was a snap. i took the back cover off i may not have had to do that but i was replacing the cook top anyway. so 4 screws and two quick electrical connectors

the cook top was a little more involved but just screws. you will figure out which screws to remove. then put them back.maybe 20 screws.if you look at the bottom of the new top you can see where the screws go.this took the most time.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 4 people found this instruction helpful

Parts Used:
  • Bake Element
Level of Difficulty: Easy
Time to do repair: 15 - 30 mins
Tools: Pliers, Screw drivers, Wrench set
Customer: Holly from Plainview, MN

Broken element and wire

Replaced it

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 4 people found this instruction helpful

Parts Used:
  • Bake Element
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Pliers, Screw drivers
Customer: (Mrs.) Jimmie from Hillsboro, TX

Baking element was out

I actually had to hire someone to fix the problem. My stove happened to be one of those they describe on the internet where the wires were not long enough to pull out. Had I tried it would have become a major repair job. The repairman had to use needle nose pliers to grab ahold of the wires and get them out far enough. All went well though and he only charged $25.00.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 4 people found this instruction helpful

Parts Used:
  • Bake Element
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Dawn from Biscoe, AR

Bake element burnt out

It is very easy shut off the power yo the stove at the fuse box, unscrew the two screws and pull the element out replace and screw back into place.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 4 people found this instruction helpful

Parts Used:
  • Bake Element
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Carol from Oldsmar, FL

The control pannel shorted out (circuit board timer)

Moved the stove, unplugged it. took the back off, took out old board installed the new one. It was just that easy and saved us from buying a new stove.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 4 people found this instruction helpful

Parts Used:
  • Bake Element
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Vincent from Big Arm, MT

Bake element burned out. Actually it broke in half.

When ordering the replacement part, read the posts on how to replace the bake element. Just follwed their lead. The only difficulty is getting a hold of the wire at the back of the range that the bake element plugs into. There wasen't much play in the wire.
PS Be sure and remove the range door or have very long arms.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 4 people found this instruction helpful

Parts Used:
  • Bake Element
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Ronald from Meridian, TX

The original element broke when dad spilled a liquid on it while still hot.

Disconnected power to the range, Took off the oven door removed two screws and disconnected the two electrical connections to the heating element. Made the two connections to the new element and replace the two holding screws. Replace the oven door and plugged in the power cord. Turned on the oven to test and was finished.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 4 people found this instruction helpful

Parts Used:
  • Bake Element
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Thomas from Green Lane, PA

Bake element burned-out.

Removed element's two mounting screws and disconnected the wire leads on each end. Connected wire leads to the new element and replaced mounting screws. Only took a few minutes to make the change. The oven is good as new.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

3 of 4 people found this instruction helpful

Parts Used:
  • Bake Element
Level of Difficulty: Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Sherry from Georgiana, AL

The bottom oven element burned out.

This was very easy. All I did was unscrew the brackets from the back of the oven holding the element. Then I removed the wires from the bad element and reversed the procedure adding the new element. It was easy to order the right part and I got the item in plenty of time for the Thanksgiving holiday!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 3 people found this instruction helpful

Parts Used:
  • Bake Element
Level of Difficulty: A Bit Difficult
Time to do repair: More than 2 hours
Tools: Nutdriver, Pliers, Screw drivers
Customer: Russell from Coppell, TX

Bake element shorted out, burned out hi-limit switch

-Disconnected power from oven at the circuit breaker.
-Removed oven door and racks.
-Removed two screws holding element to the rear wall.
-Carefully pulled element away from rear wall, exposing wire leads.
-Carefully detached wire leads with male Sta-Kon connectors from element ends. (Taking care not to break or weaken the wires at the connector.)
-Disposed of old element and placed new element in same position.
-Re-attached leads by very carefully sliding male Sta-Kon connectors into the new element connectors, taking care not to push too hard and bend element wire.
-Gently re-inserted element ends into wall and re-attached element to wall with original screws.
-Reconnected power and tested new element. Element did not heat.
-Disconnected power and looked for collateral damage from original element failure.
-Removed oven from wall, removed rear panel and identified the high-temperature limit switch.
-Removed Sta-Kon leads and checked switch for electrical continuity. It had none, apparently the result of the high current from original element short.
-Obtained new hi-limit switch from Part Select
-Removed and replaced hi-limit switch, re-attached leads.
-Replaced rear panel and reinserted oven in wall.
-Reconnected power and tested new element. Element heated normally.
-Returned racks to oven, re-attached door and done.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 3 people found this instruction helpful

Parts Used:
  • Bake Element
Level of Difficulty: Really Easy
Time to do repair: 15 - 30 mins
Tools: Screw drivers
Customer: barbara from greenville, SC

I had to replace my oven element as is cracked in half

after finding my part and thank god for you guys i recieved it early it only took 4 days to get here i unscrewed my old oven part and popped the new one in easier than making cookies and now i can bake til my hearts content thanks for being there for me
barbara krebs

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 3 people found this instruction helpful

Parts Used:
  • Bake Element
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Thea from Greeley, CO

Replacing broken bottom baking element

the hardest part of this repair was the wait for the element to arrive in the mail - which was in 4 business days - then took 5 to 10 minutes to get to circuit breaker box in garage. That was the longest part of the repair. My husband took the door off the oven after turning the circuit off in the garage. Followed directions from others who made the same repair and it was done in 2 minutes! Super easy - thanks for saving us money during this time of tight budgeting around the holidays! You're a lifesaver!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 3 people found this instruction helpful

Parts Used:
  • Bake Element
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Jeffrey from Steelville, MO

The lower baking element of the oven did a 4th of july sparkler show coming right out of the oven door three days before thanksgiving

I had the part overnighted since Thanksgiving was in two days and we needed to be able to use the oven. I saw a video on the website that instructed how to unplug the stove. Unscrew the baking element from the inside of back wall of oven. Gently pull out the part to where it is attached to wires. Simply pull apart the male part from female parts. Replace the old element with new element and attach it to the pulled out wires. Then gently push back wires inside the back wall of oven. Screw the attachment back in. We then plugged the oven back in. Turned on the oven to about 300 degrees. We put an oven temperature gauge inside and after a time the oven temperature was at 300 degrees and steady. It was fixed. Thanksgiving was on!

Help other customers find the most helpful instructions.

Were these instructions helpful?   

2 of 3 people found this instruction helpful

Parts Used:
  • Bake Element
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Tom from Hurst, TX

Bake element went out

First I turned the power off to the oven using the breaker switch. Removed the old bake element by first unscrewing the 2 screws for each bracket holding each side of the old bake element and unplugging the two current connections.

Replugged and rescrewed above. Turned breaker on for oven. Tested by turning oven to back and watching new bake element heat up.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

1 of 1 people found this instruction helpful

Parts Used:
  • Bake Element
Level of Difficulty: Really Easy
Time to do repair: Less than 15 mins
Tools: Screw drivers
Customer: Miguel R from MCKINNEY, TX

Heating element stopped heating

I unplugged the cord to the stove. Then I removed the two screws on the broken heating element. Once the screws were removed, I slid off the two wires attached to the element prones. Grab the new element and attached the two wires. Reinstalled screws. Plugged in the cord, and turned on oven. Heating element came on.

Help other customers find the most helpful instructions.

Were these instructions helpful?   

Model Cross Reference

This part works with the following models:

PartSelect Number: PS11744404
Manufacturer Part Number: WP74010750
Brand Model Number Description
Kenmore62945775Range
Kenmore62945776Range
Kenmore62945779Range
Kenmore62946795Range
Kenmore62946796Range
Kenmore62946799Range
AmanaACS4140BBRange - Electric
AmanaACS4140BWRange - Electric
AdmiralAER1110AAHRange - Freestanding, Electric
AdmiralAER1110BAHRange
MaytagAER1140AGHRange
AdmiralAER1150AAHRange - Built-in, Electric
AdmiralAER1350AAHRange - Freestanding, Electric
AdmiralAER1350AALRange - Freestanding, Electric
AdmiralAER1350AATRange - Freestanding, Electric
AdmiralAER1350AMHRange
AdmiralAER1350BAHRange
AdmiralAER1350BATRange
MaytagAER1360AGWRange - Freestanding, Electric
MaytagAER1360BGWRange - Freestanding, Electric
AdmiralAER1450AAHRange - Freestanding, Electric
AdmiralAER1450BAHRange
AdmiralAER2350AMHRange - Built-in, Electric
AmanaAER4111AAWRange - Freestanding, Electric
AmanaAER4311AAWRange - Freestanding, Electric
AmanaAER5511AABRange - Freestanding, Electric
AmanaAER5511AAQRange - Freestanding, Electric
AmanaAER5511AAWRange - Freestanding, Electric
AmanaAER5511ACBRange - Freestanding, Electric
AmanaAER5511ACWRange - Freestanding, Electric