Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS11744404
This bake element has push-on terminal ends.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
First, I unplugged the oven. Then, I removed the two screws that hold the element in place. After that, I gently pulled the element toward the front of the oven until the wires were exposed. I disconnected the wires from the old element, removed the old element and then attached the wires to the new baking element. I gently pushed the new element back into the screw holes and screwed the new element in place. When I plugged the oven back into the wall I heard a pop and thought I'd blown up the oven! Turns out the breaker popped...after fixing the breaker, I turned the oven on and the element worked just fine. I highly recommend PartSelect.com for their fast shipping and great products. I will be ordering from them again for future appliance parts.
Help other customers find the most helpful instructions.
Were these instructions helpful?
First, I shut off power to stove(a must).Removed two screws that hold element in place.Gentley pulled element toward door opening.Once wire is expose, hold back of element and pull gentley to seperate element from wire slot.Connect new element to wire and replace screws.
This was easier than putting in a new light switch. The old receptacle would not make the necessary adjustments to the heat element to maintain the desired temperature. Even when I turned the temperature knob to "minimum", the heat element would bun at the maximum temperature. I pulled the element from the Receptacle, raised the stove top to expose the receptacle and wiring. My stove was too heavy to pull from the wall, so I had to go to the breaker box to flip off the breaker. I returned to the stove and snipped the non working receptacle (with a wire cutter) and attached the new receptacle with the ceramic wire nuts, that came with the assembly. I turned the electric-breaker back on, and tested the heat element. The element will now make the on/off adjustments on each temperature setting, to maintain the correct heat. I ordered two receptacles because I wanted a spare. I do a lot of baking during special-day dinners, for my family members... and due to the age of my stove, I bought the bake element as a "back up" if the present Bake-element burns out.
I looked at the other repair stories on this site & realized it should be simple to do. I first switched off the power at the circuit breaker (range has its own switch). Then used a philips head screw driver to remove the 2 screws that hold the element in place at the back of the oven. Gently pulled the element out. Was able to disconnect the wire on the right side. But the other one would not budge. Thought I would have to get a repair guy out after all. Decided to try again again next day. Put on a pair of leather gloves to get a better grip on the wire (thought pliers might bend the connectors). Was able to wiggle it back & forth & it came loose. Then it was easy to hook up the new one, gently pushing the element connectors into the oven wires & put it back into the oven & replaced the 2 screws holding the element in place. Switched the circuit breaker back on. Turned on the oven and it works like new and no repair person visit!! Thanks for the info at this site.
Real easy to do. I just unscrewed from back pulled out until wire can out of back then seperated from wire. Took out element put new one in. Real easy didn't even need my husband
Piece of cake! Took more time to find the screwdriver than it did to replace the element!Unplugged the stove. Removed 2 screws. Pulled the element out about 2" and disconnected the wires on each end (wires are attached to a metal clip that just pushes on to the end of the element. Threw the old element away. Unpacked the new elements. Connected the wires at each end. Pushed element into place and screwed in 2 screws. Plugged oven/stove back in and voila! That's it!
very very easy. but keep in mind that step one, killing the power at the power box. I jumped that one to a near disastours outcome, thankully all turned out well byt there was a hell of bang and VERY bright flash. Still was worth "doing it yourself" just keep in mine the cut power side...Safety first!!!
This was a complete no brainer. The easiest repair I have ever done. Take out the old screws, remove element and replace with new one, replace screws. Took less than 5 minutes :)
Replacing the sensor kit and door gasket was no problem at all, however the baking element was A different story.The problem was not the fault of the replacement part, but the removal of the element to be replaced. The phillips head screws stripped out very easy and getting them out without damage to the interior finish of the oven was time consuming and challenging, but patients, and perservrancewin and so did I. Oven now works great
removed the screws,pulled the element out about 3 inches disconnected the 2 wires
Very easy repair. Turn the power off to the oven, take out two screws and unhook electrical connections. Replace with the new baking element and you are done. Takes only about 10 minutes and the oven works like new.
First, I removed the two screws that hold the element in place. I then tried to pull the element out to disconnect the wires attached to the clips. The left side came right out. The right side would not. Had to pull the range out from the wall (would only come out about a foot and a half due to the gas line connection). Removed the back (2 screws). Removed the clip from the element from the rear and redirected the wire into the oven. Replaced the back, pushed the oven back, attached the wire clip and screwed the element in place. Works fine. This is definitely a job not requiring an electrician.
Removed the oven door and oven racks. Turned off the power to the range/oven. Unscrewed the bottom element and place the new element in its place. Screwed element in and replaced the oven door and racks. Turned the power back on and turned the oven on. It works great.
When ordering the replacement part, read the posts on how to replace the bake element. Just follwed their lead. The only difficulty is getting a hold of the wire at the back of the range that the bake element plugs into. There wasen't much play in the wire.PS Be sure and remove the range door or have very long arms.
Disconnected power to the range, Took off the oven door removed two screws and disconnected the two electrical connections to the heating element. Made the two connections to the new element and replace the two holding screws. Replace the oven door and plugged in the power cord. Turned on the oven to test and was finished.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2016 , Eldis Group Partnership. All rights reserved.