Have you ever purchased from PartSelect.com before?
Thank you for helping make our site better.
PartSelect Number PS11744015
This electric oven bake element with female spade connections is 16 inches long and 19 inches wide. It has a terminal depth of three inches, making a total element length of nineteen inches.
This part works with the following brands: Whirlpool, Admiral, Estate, Inglis, Kenmore, KitchenAid, Roper, Maytag, Crosley, Jenn-Air, Hardwick, Magic Chef, Amana, Caloric & Glenwood.
This part fixes the following symptoms:
Very simple process of diagnosing. Toughest part was finding the part. Part Select mad it very easy, inexpensive and great service and delivery right on time. What a great site. Will always come here first.
Help other customers find the most helpful instructions.
Were these instructions helpful?
First off, because of weather delays, it took FedEx 8 days to deliver part, finally had to drive 3 miles out our road to meet driver.The connectors were females on the new part as were the connectors in the range. Had to cut off oven connectors and replace with males. Fortunately, I had the connectors (not supplied) and knew how to attach them.
I ordered the only part that looked like it would fit. First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. But the new replacement had the wrong ends to fit right. I was going to email you back to see if there were other options for me, when a friend came by and said he would just replace the oven connecting ends and then it would work. Luckily he had extra little ends at home, came over and replaced the ends, cutting the old ones off of the oven side. He wire stripped the wire, attached the new ends and crimped and then reattatched the whole heating element. Without his know-how, I would have had to have a repair man come and do the same thing for me, or go buy a new stove.....but it is simple when you know how!! It would have been helpful to me, to have the description of the ends of the new element I was buying..... whether it was male or female... but it is fixed now, thanks to my friend. A steak dinner was cheaper than a repair man!!!!
After removing two screws, I pulled the bake element free from the oven's female electrical connections---only to find the new element had female connectors, too. Nevertheless, I cut the male connectors off the old bake element and used them as a splice (of sorts). Then installing the new bake element was a piece of cake, which I can make now thanks to PartSelect.com.
First I remove th screw that held the element in place then I pulled the element out and disconnect the wires. Then I replace the new element, I connected the wires back then I put the screws to hold the element.
I followed the instructions that were posted on the web site for the replacement of the element. I found everything exactly as described in the procedure. I disconnected the two screws that held the old element, removed the old element, inserted the new element and replaced the screws. I turned the oven control on and the element heated up. Everything has been working just fine.
Took four screws out, pulled old one out and disconnected two wires and waited for new part to be delivered. installed part in one minute. I had the same thing happen 5 years ago and the repair person charged me $150. This time it cost me $40 .
Turned off power at breaker box. Removed two screws from the old bake element on rear of oven wall. Pulled out bake element from back of oven so wires were exposed (about 3-4 inches). By hand, removed the wire connector from each side of the element (wiggle it loose). The part I purchased was exactly as described on the PartSelect website (i.e., it had the correct connections - female - on the bake element). The part arrived in 2 days in perfect condition. I definitely will use PartSelect again.
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires. That is when I notice that the new element had a female connector and so did my wires comeing out of the stove. I took the old elements male end off (with a grinder). The mail end was long enough to use it connect both female end.
This was a very easy repair and the website helped greatly. my husband simply pulled old element out and pluged the new one in. Excellent website, saved us a lot of money.
All brand logos are trademarks of their respective owners.
The PartSelect logo is a Registered Trademark of Atlantic Laundry Centres, Ltd.
Copyright © 1999-2016 , Eldis Group Partnership. All rights reserved.